NOTE:
If the DVD/VCR key did not blink twice after
entering the codes last digit, repeat steps 2 and 3 and
try entering the same code again. If you’ve located
a setup code that works for your combo device (for
example, a TV/VCR Combo) and a separate TV code
is also listed, you’ll need to program this code into
the remote control to access volume control (see the
“Programming Device Control” section).
!IMTHEREMOTECONTROLATYOURCOMBODEVICEFOR
EXAMPLE466#2#OMBO ANDPRESS0/7%2ONCE
The device should turn off. If it does not respond,
repeat steps 2 and 3, trying each code listed for your
brand until you find one that works. If it still does not
RESPONDTRYSEARCHINGFORTHECODESEETHEh3EARCHING
FOR9OUR#ODEvSECTION
5. For future reference, write down each working device
code in the boxes below:
466#2OR46$6$#ODE
46#ODEIFUSED
Searching For Your Code
If your home entertainment device does not respond to the
OARP05S Cable Replacement Remote after trying all of the
codes listed for your brand, or if your brand is not listed at
all, try searching for your code.
&OREXAMPLETOSEARCHFORACODEFORYOUR46
4URNONYOUR46
/NTHEREMOTECONTROLPRESS46ONCEITWILLBLINKONCE
4HENPRESSANDHOLD3%450UNTILTHE46KEYBLINKSTWICE
%NTER4HE46KEYWILLBLINKTWICE
!IMTHEREMOTECONTROLATTHE46ANDPRESS0/7%2ONCE
5. Press and release the CH+ key continuously, then stop
WHENTHE46TURNSOFF
NOTE:
In the search mode, the remote control will send
IR codes from its library to the selected device, starting
with the most popular code first.
0RESS0/7%24HE46SHOULDTURNONTHENPRESS3%450
ONCETOLOCKINTHECODE4HE,%$WILLBLINKTWICETO
indicate that the code is saved.
NOTE:
If the TV does not turn on during step 6, then
slowly press and release CH- to go back through the
codes, then press SETUP when the TV turns on.
4ESTOTHERREMOTECOMMANDSFORTHE46EGVOLUME
MENUETC )FTHECOMMANDSYOUWANTTOUSEWITHYOUR
46WORKYOUVElNISHEDPROGRAMMINGFORYOUR46)F
they don’t, repeat steps 1-4 above. In step 5, don’t stop
WHENYOUR46TURNSOFFTHElRSTTIMEKEEPPRESSING
CH+ until it turns off again.
NOTE:
By default, the CH+/- keys change channels on
the CBL/SAT device regardless of what mode you’re in.
So, you should only use these keys to test for CBL/SAT
device codes at this point.
8. To search for the codes of your other devices, repeat
steps 1 through 6, but substitute the appropriate key
EG$6$6#2$62!58!5$OR#",3!4 FORTHE
device you’re searching for.
Checking the Codes
If you have set up your remote control by searching for
your device code, you may need to find out which four-
digit code is operating your equipment.
&OREXAMPLETOlNDOUTWHICHCODEISOPERATINGYOUR46
/NTHEREMOTECONTROLPRESS46ONCEITWILLBLINKONCE
4HENPRESSANDHOLD3%450UNTILTHE46KEYBLINKSTWICE
%NTER4HE46KEYWILLBLINKTWICE
3. To view the code for the first digit, press 1 once. Count
THENUMBEROFTIMESTHE46KEYBLINKSEGBLINKS
ANDWRITEDOWNTHENUMBERINTHELEFTMOST46#ODE
BOXINTHEh0ROGRAMMING$EVICE#ONTROLvSECTION
NOTE:
If a code digit is 0, the selected mode key will not
blink.
4. Repeat step 3 three more times for the remaining
digits. Use 2 for the second digit, 3 for the third digit,
and 4 for the fourth digit. Finish writing down the code
INTHE46#ODEBOXES
5. To check for other device codes, repeat steps 1 through
BUTSUBSTITUTETHEAPPROPRIATEKEYEG$6$6#2
$62!58!5$OR#",3!4 FORTHEDEVICEYOUARE
CHECKING7RITEDOWNTHECODESINTHEAPPROPRIATE
BOXESINTHEh0ROGRAMMING$EVICE#ONTROLvSECTION
Using Learning
The OARP05S Cable Replacement Remote includes a
,EARNINGFEATURESOYOUCANADDFUNCTIONSTHATAREUNIQUE
TOYOURHOMEENTERTAINMENTDEVICESEG6#2TRACKINGUP
ORDOWN
Learning Precautions
s
9OURORIGINALREMOTECONTROLSMUSTBEINWORKINGORDER
for learning to work properly.
s
,EARNEDKEYSAREMODESPECIlCSOEACHONECANSTOREA
unique function for each mode.
s
$ONOTUSETHEFOLLOWINGKEYSFORLEARNINGDEVICEKEYS
3%450 2ECORD -ACROKEYS
s
,EARNINGCAPACITYISUPTOATOTALOFKEYSDEPENDING
on the code being learned.
s
#ERTAINDEVICEFUNCTIONSARENOTLEARNABLEINCLUDING
multi-frequency types, some high frequency ones, and
other unusual formats.
s
&OROPTIMUMLEARNINGAVOIDHIGHLEVELSOFAMBIENT
light such as natural sunlight or energy-efficient
fluorescent lights.
NOTE:
Please have your original remote controls handy
before programming learning.
Programming a Learned Key
NOTE:
If more than 15 seconds pass between key
presses, the remote exits programming.
0RESSANDHOLD3%450UNTILTHELASTSELECTEDMODEKEY
BLINKSTWICETHENPRESS
NOTE:
If the LED displays one long flash instead,
either your batteries are low, or the OARP05S Cable
Replacement Remote has a memory fault.
0RESSAMODEKEYONCEIE$6$6#2$62!58!5$
46OR#",3!4 TOASSIGNAMODEFORLEARNING
3. Press the desired key on the OARP05S once to store the
feature to be learned.
0LACETHE/!2032EMOTE#ONTROLHEADTOHEADABOUT
vAPART FROMYOURORIGINALREMOTECONTROL!LSOLOCATE
THEKEYONYOURORIGINALREMOTECONTROL THATYOUWANT
the OARP05S Cable Replacement Remote to learn.
2"
5. On the original remote, press and hold the key to be
LEARNED4HEDEVICEKEYS,%$WILLBLINKRAPIDLYTHEN
turn off. Continue holding the key on the original
REMOTEUNTILTHEDEVICEKEY,%$BLINKSTWICE
NOTE:
If the LED displays one long blink, a learning
error has occurred. Try repeating this step again until
a successful capture occurs. If the function is still not
captured, press and hold SETUP to exit programming
and review the “Learning Precautions” earlier in this
section. If needed, also see “Troubleshooting” later in
this manual. After review, start programming again at
step 1.
2EPEATSTEPSTHROUGHFORANOTHERMODEANDORKEY
ORPRESSANDHOLD3%450UNTILTHEACTIVEMODEKEY,%$
blinks twice to exit programming.
