RCVR to CBL/SAT SETUP* + 992 + CBL/SAT + RCVR +
RCVR + SETUP* +
Cable/DBS code
CD to TV
SETUP* + 992 + TV + CD + CD +
SETUP* +
TV code
CD to VCR
SETUP* + 992 + VCR + CD + CD +
SETUP* +
VCR code
CD to DVD/LD
SETUP* + 992 + DVD/LD + CD + CD +
SETUP* +
DVD or LD Player code
CD to RCVR
SETUP* + 992 + RCVR + CD + CD +
SETUP* +
Audio code
CD to CBL/SAT
SETUP* + 992 + CBL/SAT + CD + CD +
SETUP* +
Cable/DBS
code
CBL/SAT to TV
SETUP* + 992 + TV + CBL/SAT + CBL/
SAT + SETUP* +
TV code
CBL/SAT to VCR
SETUP* + 992 + VCR + CBL/SAT +
CBL/SAT + SETUP* +
VCR code
CBL/SAT to DVD/LD SETUP* + 992 + DVD/LD + CBL/SAT +
CBL/SAT + SETUP* +
DVD or LD code
CBL/SAT to RCVR SETUP* + 992 + RCVR + CBL/SAT +
CBL/SAT + SETUP* +
Audio code
CBL/SAT to CD
SETUP* + 992 + CD + CBL/SAT + CBL/
SAT + SETUP* +
CD Player code
*NOTE: Here (*) you must hold SETUP until the Cinema 6’s
red light blinks twice.
PROGRAMMING THE MACRO KEYS
The
Cinema 6
has two Macro keys
(
MACRO and MACRO2
)
that allow the user to play back a series of keystrokes, at any
time, with the press of one key. For example, to set up a
sequence that will turn on your components and change the
components to the proper inputs:
1.
Press and hold SETUP until the
Cinema 6’s red
light blinks twice, then release
SETUP.
2.
Press 9 - 9 - 5. The
Cinema 6’s red light will
blink twice.
3.
Press and release one of the MACRO keys.
This will be the key that will play back the
series of keystrokes assigned to that key.
4.
Begin entering the sequence of keystrokes, up
to 15, that you wish to be played back when
you press the MACRO key. For example:
RCVR + POWER + TV + POWER + TV/VCR
(To change the input on the TV to VIDEO 1) +
CBL/SAT + POWER.
5.
Once your sequence is entered, press and hold
SETUP until the
Cinema 6’s red light blinks
twice.
Now, using the example above, whenever the programmed
MACRO key is pressed, the Receiver would power ON, the
TV will power ON and change the input to VIDEO 1 and
then the Satellite would power ON.
Repeat steps 1 - 5 to then setup a second sequence on
the
MACRO2 key.
VOLUME LOCK
Volume Lock allows the user to designate which compo-
nent will control the volume in the
TV
,
DVD/LD
and
CBL/
SAT
modes. To set the Volume Lock to the
TV mode:
1.
Press and hold SETUP until the
Cinema 6’s red
light blinks twice, then release
SETUP.
2.
Press 9 - 9 - 3. The
Cinema 6’s red light will
blink twice.
3.
Press and release TV. The
Cinema 6’s red light
will blink twice.
9-9-5
9-9-5
9-9-3
9-9-3
Now, whenever you press
VOL
▲
,
VOL
▼
or MUTE in the
VCR
,
DVD/LD
and CBL/SAT
modes your TV will control the
volume. If you would like to change the Volume Lock setting
to the
VCR
,
DVD/LD
or CBL/SAT
modes repeat steps 1-3,
only substitute the appropriate device key. Setting the
Volume Lock to the
TV
,
VCR
,
DVD/LD or CBL/SAT
mode will
not effect the volume control in the RCVR
and CD
mode.
You can also change the Volume Lock setting so that an
Audio component controls the volume in all device modes. To
change the Volume Lock setting on the
Cinema 6
to the
RCVR or
mode:
1.
Press and hold SETUP until the
Cinema 6’s red
light blinks twice, then release
SETUP.
2.
Press 9 - 9 - 3. The
Cinema 6’s red light will blink
twice.
3.
Press and release RCVR. The
Cinema 6’s red
light will blink twice.
Now, whenever you press
VOL
▲
,
VOL
▼
or
MUTE
your Audio
component will control the volume in all device modes.
You can also change the Volume Lock setting so that each
component controls its own volume. However, some
components do not have volume control. Using this setting
may eliminate volume control in some device modes. To
change the Volume Lock setting on the
Cinema 6
so each
mode controls its own volume:
1.
Press and hold SETUP until the
Cinema 6’s red
light blinks twice, then release
SETUP.
2.
Press 9 - 9 - 3. The
Cinema 6’s red light will blink
twice.
3.
Press and release VOL
▲
. The
Cinema 6’s red
light will blink twice.
Now, whenever you press
VOL
▲
,
VOL
▼
or
MUTE on the
Cinema 6 each component will control its own volume,
provided each component has volume control.
9-9-3
9-9-3
9-9-3
9-9-3
USING THE SLEEP KEY
The SLEEP key allows you to access the sleep timer of
your TV, Cable Converter/DBS Satellite or Audio compo-
nent. You can access your TV, Cable Converter, DBS
Satellite or Audio component’s Sleep Timer by pressing
the SLEEP key. Most Sleep Timers advance in increments
of 10 or 15 minutes, however, for specific instructions on
setting your components Sleep Timer, please consult your
original owners manual.
Even if your original Cable Converter remote control did
not have a sleep timer, your
Cinema 6
has its own built-in
sleep timer. If your Cable Converter does not have a sleep
timer, press the
SLEEP key to activate the
Cinema 6
’
s
built-in sleep timer. For example:
1.
Press and release the CBL/SAT key then press
the SLEEP key once to set the
Cinema 6’s
built-in sleep timer for 15 minutes. The red light
will blink once.
2.
Each additional press of the SLEEP key will
add 15 more minutes to the Sleep Timer, up to
a maximum of 60 minutes. The LED will blink
twice when the sleep timer is set for 30
minutes, 3 times for 40 minutes, or 4 times for
60 minutes.
NOTE: The sleep timer starts 10 seconds after the last
press of the SLEEP key. Once you have activated the
Cinema 6’s built-in sleep timer, you must keep the remote
control aimed directly at the component.
3.
To de-activate the built-in sleep timer, press
POWER.
NOTE: Plugging your TV into the outlet on the back of the
Cable Converter may allow you to turn both your Cable
Converter and your TV ON and OFF.
