Specifications and Performance
Item
TYPE G9SX-SM032-
III
50 ms Max.
Frequency: 10 to 55 to 10Hz,
Amplitude: 0.375mm half amplitude (0.75mm double amplitude)
-10 to +55 (No freezing or condensation)
25 to 85%RH
Approx. 200 g
Over voltage category (IEC/EN 60664-1)
Response time (ON to OFF state)
3.0 V Max.
(Safety standstill detection outputs and Auxiliary outputs)
ON-state residual voltage
0.1 mA Max.
(Safety standstill detection outputs and Auxiliary outputs)
OFF-state leakage current
(Permissible impedance : 100ohm Max. and 10nF Max.)
100m Max.
Maximum cable length for
standstill detection inputs and EDM input
Vibration resistance
Mechanical shock resistance
Ambient temperature
Ambient humidity
Weight
300 m/s
2
(destruction)
100 m/s
2
(malfunction)
Terminal block:
Main body:
IP20
IP40
Degree of protection
Detection voltage
(Standstill detection voltage)
Standard Configuration: 10mV Max.
User Configuration:
100mV Max.
Insulation specifications
Item
TYPE G9SX-SM032-
100Mohm Min. (500VDC megger)
100Mohm Min. (500VDC megger)
2000VAC for 1min
2200VAC for 1min
2200VAC for 1min
500VAC for 1min
Insulation
resistance
Dielectric
strength
- Between Standstill detection input terminals connected together and
Power supply input terminals and other input and output terminals
connected together.
100Mohm Min. (500VDC megger)
100Mohm Min. (500VDC megger)
- Between Standstill detection input terminals connected together
and DIN rail.
- Between all terminals without Standstill detection input terminals
connected together and DIN rail.
- Between standstill detection inputs (Z1,Z2
Z3,Z4)
- Between Standstill detection input terminals connected together and
Power supply input terminals and other input and output terminals
connected together.
- Between Standstill detection input terminals connected together and
DIN rail.
- Between all terminals without Standstill detection input terminals
connected together and DIN rail.
- Between standstill detection inputs (Z1,Z2
Z3,Z4)
Note:
*1. Power consumption of loads not included.
*2. Please input voltage between 2 phases to Z1-Z2 and Z3-Z4.
*3. When a motor with AC240V or more is used,connect neutral point of the power supply to earth.
*4. For EDM input, use devices with contacts capable of switching micro loads of 24VDC, 5mA.
*5. While Safety standstill detection outputs are in the ON state, signal sequence shown below is output continuously for diagnosis.
When using the Safety standstill detection outputs as input signals to control devices (e.i. programmable controller), consider the
off pulse below.
*6. The following derating is required when units are mounted side-by-side.
- 0.2 A max. load current
typ.100ms
OFF
ON
360
s
Max.
Ratings and Specifications
5
Ratings
Rated supply voltage
Power
input
Item
Inputs
Outputs
24VDC
TYPE G9SX-SM032-
-15% to +10% of rated supply voltage
4 W Max.
Standstill detection input (Z1-Z2/Z3-Z4) (*2)
480VAC max.(120Hz max.)(*3)
sourcing output(PNP)
Load current: 300mA DC max.
(*6)
sourcing output(PNP)
Load current: 100mA DC Max.
Operating voltage range
Rated power consumption
(*1)
Rated Input voltage
Standstill detection input : approx. 660kohm
EDM input : approx. 2.8kohm
(*4)
Internal impedance
Safety Standstill detection output
(*5)
Auxiliary output
- 6 -
