Omron Powli BU100RW Скачать руководство пользователя страница 68

Страница: 68 / 99

. Maintenance and Inspection

●

Replacement fan

  For BU75RW/BU100RW rear:   Model BUF100R
  For BU200RW/BU300RW rear:  Model BUF300RF
  For BU200RW/BU300RW front: Model BUF300FF

■

Fan replacement procedure

Use a screwdriver to loosen (turn counter-clockwise) and remove the cooling fan screws 4 screws.

①

(The diagram shows the BU200RW/BU300RW rear cooling fan.)

Fan replacement is complete.

Insert the fan into the unit’s fan recess.

①

Use the screwdriver to securely tighten (turn clockwise) the removed screws (4 screws for rear
fan, front fan).

②

When doing so, make sure the cable does not become pinned under the fan cover.

Insert the new fan connector until it clicks into place.

③

The beep stops, and the "EF" status display lamp turns OFF.

While pressing down on the tip of the fan connector

①

, pull it toward

you to disconnect it.

②

The beep stops, and the error lamp turns OFF.

Loosen the 4 Phillips-type screws.

Содержание Powli BU100RW




































































































Результаты поиска

Содержание Powli BU100RW

Отзывы:

Похожие инструкции для Powli BU100RW

Бренды по названию

Популярные бренды

Omron Powli BU100RW, Инструкция по эксплуатации

Результаты поиска

Содержание Powli BU100RW

Отзывы:

Похожие инструкции для Powli BU100RW

Бренды по названию

Популярные бренды