Omron E5AX-P Series Скачать руководство пользователя страница 12

Страница: 12 / 14

E5AX-P

Dimensions

Note:

All units are in millimeters unless otherwise indicated.

Communications connector
(RS-232C and BCD connector is shown.)

Communications board
(RS-422 and 485 terminals are shown.)

Communications board
(4 to 20 mA transmission output is shown.)

4 to 20 mA
transmission output

RS-422 RS-485

RDB
RDA
SG
SDA
SDB

Panel Cutout

Side-by-side Mounting
of N Controllers

+0.8
0

120 min.

L = (96N – 3.5)

Mounting
Screw

11 5

2 to 10

Installation

Note:

1. Connect a valve position indicator if required.

2. Do not connect unused terminals.

Control

output

Open

Alarm output

Potentiometer
input
(see Note 1)

100 to 240 VAC, 50/60 Hz

Ground FG terminal 18 under
noise-interfered environment.

Use these terminals when connecting a platinum
resistance thermometer (remove short bar from
terminals 14 and 15).

Use these terminals when connecting a thermo-
couple (do not remove short bar from terminals
14 and 15).

Содержание E5AX-P Series















Результаты поиска

Содержание E5AX-P Series

Отзывы:

Похожие инструкции для E5AX-P Series

Бренды по названию

Популярные бренды

Omron E5AX-P Series, Руководство пользователя

Результаты поиска

Содержание E5AX-P Series

Отзывы:

Похожие инструкции для E5AX-P Series

Бренды по названию

Популярные бренды