background image

-

take precautions suggested before;

-

use suitable tools to avoid damage to bolts and tightening screws located on the electrical
components;

-

should it be necessary to repair the end of cables to be inserted in the terminal boxes or in the
fixing  holes  of  electrical  devices, use suitable  tools  and  materials  with  a  suitable  section,
avoiding to damage the insulator;

-

register the electrical maintenance procedures carried out and any anomalies found.

IF CHECKS NEED TO BE CARRIED OUT ON ACTIVE PARTS OF THE CIRCUITS WITH 
VOLTAGE, IT IS COMPULSORY TO: 

USE ALL INDIVIDUAL PROTECTION DEVICES COMPLYING WITH THE LAW.

NEVER OPERATE ALONE: A SECOND PERSON MUST ALWAYS BE PRESENT.

When the procedures are finished, check that all removed protections have been re-
established before restoring power supply. 

About every month or every 200 working hours, while the machine is in operation, check that: 

control devices work properly (warning lights, acoustic signallers and operator panel);

safety requirements work properly (emergency button and safety limit switch in the film
roll carriage).

About every month or every 200 working hours, check that the plates indicating the functions of the 
control and emergency devices are in good conditions. 
The identification plates and writings of the control and emergency devices must allow the 
functions of the devices to be unequivocally identified. Detached or unreadable elements must be 
adequately fixed in their previous position. 

About every month or every 200 working hours, check that the insulation of the machine electrical 
feeder, and the plugs and sockets at the side of the machine are not damaged. 

About every month or every 200 working hours, carry out a visual check of the following limit 
switches: 
-

of table rotation;

-

of carriage going up and down;

-

of taping system going up and down (in the picture).

Omni

 SUPERPLUS EN IGM_REV6

 42 

Содержание Superplus











































Отзывы: