Omni Group GREEN SMART 864 Скачать руководство пользователя страница 9

Страница: 9 / 72

Installation

(for qualified installers only)

4090507

100-01217_000

Top Vent or Side Vent Configuration

This appliance is shipped in the top vent configuration. To change to the side vent configuration, follow the
directions below.

NOTE

: the vent configuration affects several aspects of installation (framing, maximum vent rise, maximum vent

run). Make sure the vent configuration is correct prior to installation. You may wish to configure the diffuser when
changing the vent configuration.

Converting the
Fireplace to Side
Vent
Configuration

Remove the back plate on
the fireplace.

NOTE

: Use a magnetic-tipped

nutdriver on these screws -
take care to prevent the
screws from falling into the
fireplace.

Remove the flue assembly.

Tuck the two

" (

610mm

) pieces of

insulation into the area between the
exhaust manifold and fireplace can.

WARNING: Failure to properly

place the insulation will void the

warranty and create a safety
hazard.

Содержание GREEN SMART 864









































































Результаты поиска

Содержание GREEN SMART 864

Отзывы:

Похожие инструкции для GREEN SMART 864

Бренды по названию

Популярные бренды

Omni Group GREEN SMART 864, Руководство по установке

Результаты поиска

Содержание GREEN SMART 864

Отзывы:

Похожие инструкции для GREEN SMART 864

Бренды по названию

Популярные бренды