Omni Group GREEN SMART 864 Скачать руководство пользователя страница 53

Страница: 53 / 72

Finalizing the Installation

(for qualified installers only)

4090507

100-01217_000

Follow the directions below to remove the outer burner and replace the orifices.

Remove the
outer burner.

Use a 1/2” open end wrench to unscrew the two orifices.

Screw each LP orifice in
so the orifice protrudes
15/16” (23.8mm)
indicating full insertion.

Look here for the orifice
identification

Apply thread sealant to
the LP orifices prior to
installation. Use the
chart below to identify
the correct orifices.

Center

Outer

#48
#44

#55
#55

Center Burner Orifice

1/2" Wrench

Outer Burner Orifice

Manifold

15/16”

23.8mm

Center Burner Orifice

Outer Burner Orifice

Remove this mixing tube cover.

Make sure this gasket is
replaced when re-installing.

Содержание GREEN SMART 864









































































Результаты поиска

Содержание GREEN SMART 864

Отзывы:

Похожие инструкции для GREEN SMART 864

Бренды по названию

Популярные бренды

Omni Group GREEN SMART 864, Руководство по установке

Результаты поиска

Содержание GREEN SMART 864

Отзывы:

Похожие инструкции для GREEN SMART 864

Бренды по названию

Популярные бренды