background image

 

864 See Through 

GreenSmart™ 

Fireplace 

Tested and Listed by  

 

OMNI-Test Laboratories, Inc. 

Portland, Oregon 

Report # 028-F-84-5 

ANSI Z21.88b-2003 

 

Built-In Direct Vent Fireplace 

 

Natural Gas or Propane 

 

Residential or Mobile Home

 

WARNING: 

If the information in these instructions is not followed exactly, a fire or 
explosion may result causing property damage, personal injury or loss of 
life. 

-  Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this 

or any other appliance. 

WHAT TO DO IF YOU SMELL GAS 

•  Do not try to light any appliance. 
•  Do not touch any electrical switch; do not use any phone in your building. 
•  Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's 

instructions. 

•  If you cannot reach your gas supplier, call the fire department. 
-  Installation and service must be performed by a qualified installer, service agency or the 

gas supplier. 

 

This appliance may be installed in an aftermarket permanently 

located, manufactured home (USA only) or mobile home, where 
not prohibited by local codes. 

This appliance is only for use with the type(s) of gas indicated on 
the rating plate.  A conversion kit is supplied with the appliance.

 

 

Installation Manual 

Installer

After installation give this manual to the home-
owner and explain operation of this heater. 

©

 Copyright 2009, T.I.          $10.00       100-01217_000          4090507

 

www.travisproducts.com 

4800 Harbour Pointe Blvd. SW 

Mukilteo, WA  98275

 

Содержание GREEN SMART 864









































































Отзывы: