manualshive.com logo in svg

Omicron MPD 800, Руководство пользователя

Поделиться
Скачать
Omicron MPD 800 Скачать руководство пользователя страница 26

MPD 800 User Manual

26

OMICRON

2.2.4

RBP1

 rechargeable battery pack

Designated use

Figure 2-13: Rechargeable battery pack (

RBP1

)

RBP1

 is a rechargeable lithium-ion battery pack provided by OMICRON for operating measuring devices 

without the local power supply. 

RBP1

 can be stacked to increase the available capacity. You can 

connect up to five 

RBP1

 rechargeable battery packs to power long-time measurement setups.

RBP1

 must be used and charged properly. Before using 

RBP1

, you must read and understand the 

following warning messages. If you have any question, contact the OMICRON technical support.

WARNING

Death or severe injury caused by fire and burns possible

► Do not drop or crush, do not short circuit, do not open, and do not expose the battery 

to high temperatures.

► Do not immerse the battery in any liquids.
► Do not charge the battery in flammable environment.
► Do not charge it below 0 ºC/32 ºF and above 40 ºC/104 ºF and do not operate it below 

–20 ºC/–4 ºF and above 55 ºC/131 ºF

► Never charge the battery near flammable objects.
► Do not deep discharge the battery and recharge it regularly during storage.
► Dispose of the battery properly, it may explode if damaged or disposed of in fire.
► Read this User Manual before charging the battery and use the specified charger only. 

Follow the local ordinances and/or regulations for usage of lithium batteries.

Содержание MPD 800




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды