Omicron MPD 800 Скачать руководство пользователя страница 25

Страница: 25 / 67

OMICRON

MPD 800 measurement system

Indicators

Figure 2-12:

MCU2

indicators (LEDs)

MCU2

is equipped with two

STATUS

indicators (blue and red LEDs) that display the status or

malfunction of the multi-device control unit.

The following tables depict the condition and description of the two LEDs.

Table 2-2: Blue LED indications (on the left-hand side)

Condition

Description

Flashing
(A short switch-on phase
and long switch-off phase)

Device is powered and in standby mode.

Blinking
(The switch-on and
switch-off phases are of
the same length)

Device is powered and in active mode. A secondary malfunction or error
was detected and performance might be affected negatively. Check the
fiber-optic connection.

Note:

In case of malfunction, contact the OMICRON technical support

(see "Support" on page 66).

Continuous on

Device is powered and in active mode.

Continuous off

Device is not powered.

Table 2-3: Red LED indications (on the right-hand side)

Condition

Description

Flashing
(A short switch-on phase
and long switch-off phase)

Enumeration of the device was unsuccessful.

Blinking
(The switch-on and
switch-off phases are of
the same length)

A malfunction or error has been detected. Device is not working properly
and might be performing a cool-down.

Note:

In case of malfunction, contact the OMICRON technical support

(see "Support" on page 66).

Continuous on

Device performs a self-check during power-up.

Continuous off

No malfunction or error has been detected.

Blue LED

Red LED

Содержание MPD 800




































































Результаты поиска

Содержание MPD 800

Отзывы:

Бренды по названию

Популярные бренды

Omicron MPD 800, Руководство пользователя

Результаты поиска

Содержание MPD 800

Отзывы:

Бренды по названию

Популярные бренды