manualshive.com logo in svg

Omicron DANEO 400, Руководство пользователя

Поделиться
Скачать
Omicron DANEO 400 Скачать руководство пользователя страница 24

DANEO 400 

 

24 

4.5 

Storage interface 

This is an USB host port for connecting an external mass storage device, such as an external hard 
disk or a flash drive. 

The setting to save recordings on this external mass storage is made in the Recording section 
(Storage) of DANEO Control. 

4.6 

Extension Interfaces 

Accessories for DANEO 400 can be connected to these ports when available. 

4.7 

Binary outputs 

These are four potential free relay contacts. The contacts can be activated by a post-trigger action to 
signal the detection of a trigger condition, for example to trigger other devices. 

The settings are made in the Recording section (Post-trigger) of DANEO Control. 

4.8 

Analog/binary inputs 

These are ten inputs that can be either used as analog or binary inputs. 

The configurations are made in Measurement System section (Inputs) of DANEO Control. 

Содержание DANEO 400

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды