manualshive.com logo in svg
background image

The system may be "Disarmed" by any of 2 methods:

1) 

Remote Control Disarming:   Press & Release the “Disarm” button

Upon Disarm: • The siren will chirp twice. 

(4 chirps if alarm has activated & reset)

• The parking lights will flash twice. 

(4 times if alarm has activated)

• The starter interrupt will disengage.
• The LED Status Indicator turns off

Disarming the Alarm

2)  Emergency Override:

   THEN WITHIN
   10 SECONDS

Page 3

 Step 1:

With the system in the armed condition use your key, turn the

  ignition to the "On" position.

 Step 2:

Within 10 seconds, Press & Release the Valet/  Override Switch.

System  Armed & Activated

Regardless of the method used to Arm the alarm, once Armed, the alarm will
monitor all protected zones, and if an intrusion attempt is detected it will activate,
or “trigger”.

A trigger consists of the following:

• The electronic siren will start sounding.
• The parking lights will flash on and off repeatedly.

An activation has a 30 second duration unless the system is disarmed using the
remote control or the Valet /Override switch. If all protected zones are secure at
the end of the trigger, the system will stop and rearm itself to detect further entry
attempts. If a protected zone is still open at the end of the trigger cycle, the alarm
will continue to re-trigger itself for up to six activated cycles before it resets itself
and ignores the violated zone.

Содержание MC-1














Отзывы: