4
WARNING: Disconnect all power to the unit before
installing Plug-in cards.
Adding Option Cards
The LDP63000 series meters can be fitted with up to three optional plug-in
cards. However, only one card from each function type can be installed at a
time. The function types include Setpoint Alarms (LDP6-CDS), Communications
(LDP6-CDC), and Analog Output (LDP6-CDL). The cards can be installed
initially or at a later date. Each optional plug-in card is shipped with installation
and programming instructions.
COMMUNICATION CARDS (LDP6-CDC)
A variety of communication protocols are available for the LDP63000 series.
Only one of these cards can be installed at a time. When programming the unit
via DP6-SOFT, the RS232 or RS485 Cards must be used.
SETPOINT CARDS (LDP6-CDS)
This series has four setpoint alarm output plug-in cards. Only one of these
cards can be installed at a time. (Logic state of the outputs can be reversed in
the programming.) These plug-in cards include:
LDP6-CDS10 - Dual Relay, FORM-C, Normally open & closed
LDP6-CDS20 - Quad Relay, FORM-A, Normally open only
LDP6-CDS30 - Isolated quad sinking NPN open collector
LDP6-CDS40 - Isolated quad sourcing PNP open collector
LINEAR DC OUTPUT (LDP6-CDL)
Either a 0(4)-20 mA or 0-10 V retransmitted linear DC output is available
from the analog output plug-in card. The programmable output low and high
scaling can be based on the input, max, min, or total display value. Reverse
slope output is possible by reversing the scaling point positions.
LDP6-CDL10 - Retransmitted Analog Output Card
UNITS LABEL
The LDP63000 Display has an area on the front panel designed for a custom
units label. The units label is applied directly to the panel in the embossed area.
The units backlight is then turned on via programming.
Available on 5-digit version only. Refer to the LDP63000 Accessories
Bulletin for a list of available units labels.
PROGRAMMING SOFTWARE (DP6-SOFT)
DP6-SOFT is a Windows® based program that allows configuration of the
LDP63000 meter from a PC. The software offers standard drop-down menu
commands, that make it easy to program the meter. The unit program can then
be saved in a PC file for future use. A serial plug-in card is required to program
the meter using the software.
6.
ENVIRONMENTAL CONDITIONS
:
Operating Temperature Range: Determined by the input module type
Storage Temperature Range: -40 to 60°C
Operating and Storage Humidity: 0 to 85% max. RH (non-condensing)
Altitude: Up to 2000 meters
7.
MOUNTING REQUIREMENTS
:
Max. panel thickness is 0.375" (9.5 mm)
Min. panel thickness for NEMA 4/IP65 sealing is 0.060" (1.57 mm)
8.
MODULE INSTALLATION
:
24-pin shrouded connector on LDP63000 engages connector on input module
upon installation. Shroud ensures proper alignment by providing a lead-in for
the module connector.
9.
CONNECTIONS
: All wiring connections are made to the module via high
compression cage-clamp terminal blocks. Wiring instructions are provided.
CAUTION: DISCONNECT ALL POWER BEFORE
INSTALLING OR REMOVING MODULE
10.
CONSTRUCTION
: Steel front panel, enclosure, and rear cover with
textured black polyurethane paint for scratch and corrosion resistance
protection. Sealed front panel meets NEMA 4/IP65 specifications for indoor
use when properly installed. Installation Category II, Pollution Degree 2.
Panel gasket and keps nuts included.
11.
WEIGHT
: 2.7 lbs (1.2 kg) (
less module
)
OPTIONAL PLUG-IN CARDS AND ACCESSORIES
LDP6-CDC1C - RS485 (Connector)
LDP6-CDC20 - RS232 (Terminal)
LDP6-CDC2C - RS232 (Connector)
LDP6-CDC4C - Modbus (Connector)
LDP6-CDC10 - RS485 (Terminal)
LDP6-CDC40 - Modbus (Terminal)
P
art
N
umber
I
NformatIoN
LDP63000-S-LV
Strain Gage Input, 11-36 VDC/24 VAC power
LDP63000-S
Strain Gage Input, 85-250 VAC power
LDP63000-E-LV
Process Input, 11-36 VDC/24 VAC power
LDP63000-E
Process Input, 85-250 VAC power
LDP63000-AC
True RMS AC Current and Volt Input, 85-250 VAC power
LDP63000-DC-LV
DC Current and Volt Input, 11-36 VDC/24 VAC power
LDP63000-DC
DC Current and Volt Input, 85-250 VAC power
LDP63000-T-LV
Temperature Input, 11-36 VDC/24 VAC power
LDP63000-T
Temperature Input, 85-250 VAC power
PART NUMBERS
DESCRIPTION
