![background image](http://html.mh-extra.com/html/omega/crime-guard-810i6/crime-guard-810i6_operation-manual_736687020.webp)
The Status Light
The Status Light visually confirms the status of the system and provides a high
level of visual deterrence. Two colors are shown- Red for security operations, and
Green for remote starting operations. Combinations of both colors are seen when
the two operations are occurring together. The Status Light is in the window unit,
and actually consists of two LED lights, with identical operation, for maximum
visibility.
Security System Status:
The Red colored operations of the Status Light
indicate the status of the security system:
1) Off = The security system is disarmed and not performing automatic functions.
The remote starter system is off, but in standby mode.
2) On Red Constant = The security system is in the Valet Mode, with the remote
starter system off and in standby mode.
3) Flashing Slow Red = The security system is fully armed, with the remote starter
system off and in standby mode.
4) Flashing Fast Red = Last Door Arming or Automatic Rearming is in progress,
with the remote starter system off and in standby mode.
Page - 20
Automatic Transmitter Verification:
For the first 10 seconds after the vehicle’s
ignition is turned on, the Status Light will flash Red a number of times that equal the
number of transmitters that are capable of operating the system:
5) 1 Red Flash /pause = 1 transmitter is programmed.
6) 2 Red Flashes /pause = 2 transmitters are programmed.
7) 3 Red Flashes /pause = 3 transmitters are programmed.
8) 4 Red Flashes /pause = 4 transmitters are programmed.
Zone Violation:
If the system enters an alarm condition, the Status Light will stop
flashing slow Red and begin to flash in sequence to indicate which protected zone
caused the alarm condition. The Status Light will flash and pause to indicate which
protected zone was violated while the system is still armed, after it’s disarmed, and
until the vehicle’s ignition is turned on. The system’s Zone Violation feature’s
memory can store two consecutive zone violations. If there have been multiple
Page - 21
21) Slowly Alternates Red & Green = Full Valet Mode (page 18).
22) Solid Green w/ Red Flash = Security Armed with Starting Valet Mode.
23) Solid Red w/ Green Flash = Remote starter system engaged with security
system in Valet Mode.
24) Rapidly Alternates Red & Green = Remote starter system engages and security
system armed.
25) Slow Flashing Green w/ 1 to 4 Red Flashes = This indication is during remote
start operation after disarming the alarm, and shows that the pre-
viously Armed alarm was activated and reset prior to the remote
starting. The Red flashes are the Zone Violation (previous page),
occurring with the “engine running” indicator.
26) Slowly Flashing Red 3 Times, Green 1 Time = The system is programmed
for manual transmission remote starting, and is armed and ready
for starting.
9) 2 Red Flashes / Pause = System was triggered by open hood or trunk.
10) 3 Red Flashes / Pause = System was triggered by an open door.
11) 4 Red Flashes / Pause = System was triggered by the sensor.
• Turning on the ignition will clear the Zone Violation.
violations, the Status Light will show the two most recent violations in the order in
which they occurred.
Remote Starting Diagnostics:
Whenever the system is placed into Alarm Valet
Mode, the Status Light illuminates solid Red. However, when this first occurs, the
Status Light will flash Red, then 1 to 6 Green flashes before resuming solid Red. This
indicates why the engine stopped running from the last previous remote starting.
15) Red / 1 Green Flash / Red = Programmed run time expired.
16) Red / 2 Green Flashes / Red = Brake was pressed or hood opened.
17) Red / 3 Green Flashes / Red = Engine stalled or bad tach signal.
18) Red / 4 Green Flashes / Red = Received transmitter command to stop.
19) Red / 5 Green Flashes / Red = Gear selector removed from “park”.
20) Red / 6 Green Flashes / Red = Security system triggered or low voltage.
12) Off = The remote starter system is off and in standby mode. The security
system is disarmed and not performing automatic functions.
Combination Indications:
These indications occur when security and remote
starting operations are, or have been, simultaneous.
Anti-Carjacking Protection
The system is equipped with three separate Anti-Carjacking protection features,
whose operation may be selectively activated by the ignition, by an open door, or
by the transmitter. All three are programmable, and must be turned on to operate.
Once activated, the user has 53 seconds to cancel the Anti-Carjacking protection
process by pressing the Valet Switch once. If Anti-Carjacking is not cancelled, 53
seconds after being activated the siren will begin to chirp for 7 seconds to alert the
user that the system is about to enter into an alarm condition. The Valet Switch may
Starting System Status:
The Status Light uses the color Green to indicate the
status of the remote starting part of the system:
13) Flashing Slow Green = The engine is running via the remote starting system.
14) Flashing Fast Green = A remote start command has been received, and the
system is in the process of starting the engine.
still be pressed once during this period to cancel the Anti-Carjacking process.
If the Anti-Carjacking process is not cancelled before the 60 second countdown
expires, the system will enter an alarm condition, sounding the siren and flashing the
parking lights. 30 seconds after this occurs, or should the ignition be turned off in
the meantime, the stater interrupt will engage.
Once the system enters the