To Exit any of the 3 forms of Valet Mode
, simply Press & Release the Valet
Switch at any time.
• The Status Indicator Light will turn off to confirm exit from either Alarm Valet
Mode, Starting Valet Mode, or both.
“SecureCode” allows the user to customize the number of Valet Switch presses
which are required to successfully perform an Emergency Override. The basic
Emergency Override procedure is described on pages 11-12. Instead of a single
“1 press” of the Valet Switch which would be required in order to perform an
Emergency Override, two stages of Valet Switch presses must be made. In each of
the two stages, the Valet Switch will need to be pressed 1 through 9 times, as
programmed by the user. This is the Emergency Override procedure if the system
has programmed with a customized SecureCode:
Step 1
With the system in the armed condition, enter the vehicle via the driver's
door (be aware that the system will activate to an alarm condition when the
SecureCode
Page - 19
Once the system is disarmed, if Valet Mode is desired, just press and hold the
Valet Switch for 2 seconds to place the system into Valet Mode. Should a mistake
be made entering the SecureCode, after a failed attempt to achieve SecureCode, the
ignition switch must be turned off, then on again before another attempt is made.
door is opened).
Step 2
Using the ignition key, turn the vehicle’s ignition switch on.
Step 3
Within 5 seconds press and release the Valet Switch the same number of
times that have been programmed for stage #1.
Step 4
After a few seconds, the siren will stop sounding, chirp once, and then
resume sounding.
Step 5
Now, within 5 seconds press and release the Valet Switch the same number
of times that have been programmed for stage #2. Within a few seconds
the siren will stop sounding, and the unit will disarm.
Unauthorized Transmitter Alert
TM
is a protection feature which may be turned
on by the user (see the next section, “How to Program Transmitters”). When this
protection feature is utilized, whenever a transmitter is added to operate the system,
for 48 hours afterward a warning consisting of a brief series of siren chirps sounds
every time the vehicle’s ignition is turned on.
Also during this 48 hour warning period, the 10 second Automatic Transmitter
Verification visual display will increase to being displayed for 90 seconds instead
of 10 seconds. When this feature is used and activated, after 48 hours the warning
chirps disappear and the Status Light flashing transmitter number returns to being
displayed for 10 seconds.
Automatic Transmitter Verification
TM
shows the total number of transmitters
which can operate the system, by flashing the Status Light with this number for 10
seconds every time that the ignition key is turned on.
The system features several security safeguards in one of the most vulnerable
areas of any remotely controlled system.
Transmitter Protection
Code Jumping
TM
It is quite easy, with the proper equipment, to record an alarm
or keyless entry system’s transmitter signal, and simply play the captured signal
back to the system to defeat it. system’s Code Jumping renders such “code grabbing”
devices useless by randomly changing each signal that the transmitter sends.
Anti-Carjacking protection activated using a transmitter
has the process
start by pressing and holding buttons “
II
” and “
III
” for 3 seconds, but only if the
vehicle’s ignition is on. The Valet Switch must be pressed within 60 seconds after
this is done to cancel Anti-Carjacking. This is User Programmable Feature #19 (see
pages 24,25, and 32).
Anti-Carjacking protection activated by an open door
has the process start
should a door be opened after the vehicle is started and the engine is running. The
Valet Switch must be pressed within 60 seconds after the door is opened to cancel
Anti-Carjacking. User Programmable Feature #18 (see pages 24,25, and 32).
Page - 22
The three types of Anti-Carjacking protection features are:
Anti-Carjacking protection activated by the vehicle’s ignition
has the
process start every time the vehicle’s ignition is turned on. The Valet Switch must
be pressed within 60 seconds every time the vehicle is started to cancel Anti-
Carjacking. This is User Programmable Feature #17 (see pages 24,25, and 32).
Step 3
Within 5 seconds, perform an Emergency Override using the Valet
Switch. If the SecureCode has been customized, the correct number of
Valet Switch presses must be made.
indication is present whenever the system is in Full Valet Mode.
• There will be the single chirp reminder every time the ignition turns off. This
is for the Alarm Valet Mode part of the Full Valet Mode condition.
Should two failed SecureCode attempts be made, the system will ignore any further
presses of the Valet Switch for two minutes.
In addition to Emergency Override, if any of the three anti-carjacking features
are utilized, a correct customized SecureCode would also be required to turn off
anti-carjacking once it has become fully activated. How to program your own
customized SecureCode is explained on pages 24, 25 and 27.
Step 2
Turning the ignition back on.
Step 1
Turning the vehicle’s ignition off.
alarm condition, it will not respond to the transmitter, nor will the system reset
automatically after 60 seconds, and it can only be disengaged by:
