background image

Multiple  Vehicle  Operation

The Comfort Start transmitter can operate two dif-
ferent vehicles equipped with Comfort Start sys-
tems.  The slide switch on the side of the transmit-
ter is utilized for this- one car can be operated in
switch position “A” and the second car in switch
position “B”.

10

Car “A”      Car “B”

The “multi-car” switch on
the side of the transmitter

v

v

To Activate the Trunk Release*:  

Press & Hold the lower transmitter

TRUNK button for 2 seconds

OPERATE OPTIONAL

TRUNK RELEASE

*

- The trunk will be released after 2 seconds.  The parking lights and Status Light
will flash twice to confirm and the doors will unlock.  Then the parking lights will
stay on for 30 seconds.  Optionally, the horn will also chirp 2 times.

* Connection of the trunk release may require additional parts, and may not be included
   in a standard installation.

Remote  Trunk  Release

31

The Gray wire has a 500mA Negative out-

put which is operated by the transmitter button with the “open trunk” icon, and this output
is designed for trunk release.  In most cases, an optional external relay will be needed,

20-Gauge Gray  Wire:

                 ( - ) Trunk Release Output

Connection If Desired

.

Ignition Switch

Connect "Switch" side of cut wire

to terminal 

#

30 of the relay.

Control
Module

Starter Motor

Orange Wire

Connect "Motor" side of cut wire

to terminal 

#

87a of the relay.

Note: Connect 12-gauge

Green starter wire to the

motor side of the cut wire

87a

30

87

85

86

Coil

87a

  

 30

85

87

 86

Relay

Schematic:

Typical Anti-Grind Relay

Configuration

Содержание Comfort Start





















Отзывы: