OM POWER OM2000+ Скачать руководство пользователя | Manualshive

Страница: 6 / 35

background image

5

2.

SAFETY INSTRUCTIONS

WARNING!

DANGEROUS HIGH VOLTAGE INSIDE!

The power amplifier is using high voltage up to 3000V DC, which is very dangerous for human life!
Read next safety instructions carefully first, before you will start to install and operate power
amplifier! NEVER VIOLATE NEXT RULES!

WARNING!

NEVER ALLOW CHILDREN to play around PA or to touch power amplifier or connected cables in
working condition, or to push anything into the case holes!

WARNING!

Never turn the amplifier on without the upper lid in place. DO NOT ATTEMPT TO SHORT OR BYPASS
safety switch under upper lid!

WARNING!

The amplifier is neither to be used in a WET or HUMID environment nor to be exposed to
RAINFALL!

WARNING!

Do not turn the amplifier ON without having connected the ANTENNA or properly rated DUMMY
LOAD! A hazardous HF voltage may build up on the antenna connector after turning the amplifier on
with no antenna or dummy load connected!

WARNING!

Before opening the upper lid of the amplifier make sure that power supply has been disconnected
AT LEAST 10 minutes allowing the electrolytic capacitors to discharge fully. Disconnect power cord
from the outlet!

WARNING!

Any work inside the PA (internal fuses replacement, tube replacement, etc.) can be carried out only
by professionally qualified person!

«
...
4
5
6
7
8
...
»

Содержание OM2000+




































Отзывы:

Нет отзывов

Похожие инструкции для OM2000+

Бренд: Questyle Audio Страницы: 6

Бренд: Peavey Страницы: 14

MA6100 - SERVICE MANUAL C

Бренд: McIntosh Страницы: 1

Бренд: Crown Страницы: 6

Бренд: Precision Power Страницы: 12

Бренд: DAPAudio Страницы: 16

Бренд: Atlas Страницы: 24

Princeton Reverb

Бренд: Fender Страницы: 32

Бренд: NXP Semiconductors Страницы: 11

IronHeart IRT120H

Бренд: Laney Страницы: 20

Бренд: Vox Страницы: 35

Бренд: ELECRAFT Страницы: 55

Бренд: Cloud Страницы: 7

Бренд: Marshall Electronics Страницы: 1

Sonic Frontiers SFS-40

Бренд: Sonic Frontiers Страницы: 6

Бренд: Technics Страницы: 10

Бренд: Ssl Страницы: 7

Бренд: Merlaud Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды