Olympus MV-1 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 18

Olympus MV-1 Скачать руководство пользователя страница 11

MV-1/MV-2 Endoscope Disinfectors

Frequently

Asked

Questions

09FQ0015 11/18

Two Corporate Center Drive, Melville, NY 11747

Copyright 2001, Olympus America Inc.

Copyright 2001 Olympus America Inc. This document and the contents contained herewith remain the property of Olympus America Inc. Reproduction of this document or any part

thereof by any means (electronic or otherwise) without the expressed written consent of Olympus America Inc. is strictly prohibited. Only printed copies with "Controlled Document -- Do

Not Copy" stamped in red are considered controlled copies. All other printed copies are considered Uncontrolled and may not contain the latest document revisions.

Preventive Maintenance (Cont’d)

Refer to

Chapter 5 in the MV-1/MV-2 Endoscope Disinfectors User/Service Manual.

Also, refer to

document #

09-WI-0240, MV-1/MV-2 Endoscope Disinfectors Confidence Test.

In order to ensure correct operation of the MV-1/MV-2, the following quality assurance procedures must be
performed on- the MV-1/MV-2 EACH day prior to the first cycle.

Contact Olympus if these procedures fail to yield the expected results.

Operational Phase

Area Of Concern

Recommendation

Before Operating

MV-1/MV-2 Water
Flow

A channel connector should be connected to each port in the
MV-1/MV-2 basin.

•

Turn the MV-1/MV-2 power switch

ON.

The power switch

is located on the right side of the MV-1/MV-2.

•

Press

START

on the MV-1/MV-2 control panel.

•

Wait for the pump to feed water through the channel

connectors.

•

Confirm that water is flowing properly through each

connector.

•

Note:

Flow volume will vary depending upon the type of

channel connector used. The water flow through the male
luer lock connector should be approximately 100 cc (4
oz.) in less than 15 seconds.

•

If the water flow through any connector appears to be

inadequate, check it again using a male luer lock
connector. This will determine if the inadequate water
flow is caused by the connector or the MV-1/MV-2.

•

Note:

Inadequate water flow may be caused by a

clogged valve or a malfunction of the main pump.

•

Press

STOP

on the MV-1/MV-2 control panel.

•

Note:

Contact Olympus if water does not flow properly

through all of the channel connectors.

Before Operating

MV-1/MV-2 Air
Flow

•

Press

MANUAL, DRAIN,

and then

START

on the MV-

1/MV-2 control panel.

•

While holding all tubing in the MV-1/MV-2 basin under

water, confirm that there is vigorous bubbling in all tubing.

•

Completely drain the water from the MV-1/MV-2 basin.

•

Press

STOP

on the MV-1/MV-2 control panel.

•

Note:

Contact Olympus if air does not flow properly

through ALL tubing.

«
...
9
10
11
12
13
...
»

Содержание MV-1



















Отзывы:

Нет отзывов