background image

Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-6RE Modular Revolving Nosepiece               

   

 

Page 11 of 18 

 

 

Revision 3 

Clean Grease from the Various Components 

Use  a  suitable  solvent  (e.g.,  acetone)  to  thoroughly 
clean  all  the  old  grease  from  the  stationary  base, 
revolving  turret,  threaded  retaining  ring,  perimeter 
bearing balls, center-pivot ball, mechanical detent stop, 
pivot-adjustment  screw,  and  the  slotted  lock  ring,  in 
preparation for reassembly. 

Reinstall Stationary Base into Revolving Turret 

Hold  the  stationary  base  such  that  the  center  pivot  is 
facing  downwards,  and  then  lower  the  stationary  base 
into the recess of the revolving turret (se

Figure 23

).   

 

Figure 23 

 Reinstall stationary base into revolving turret 

Apply Ring of Grease for the Perimeter Balls 

The next step is to apply grease into the ring into which 
the  perimeter  bearing  balls  will  be  placed.    Carefully 
apply a ring of grease (item S2 o

Appendix 1

into the 

channel  formed  between  the  outer  perimeter  of  the 
stationary base and the inner perimeter of the revolving 
turret  (see 

Figure  24

).    Do  not  apply  too  much  grease 

here, to minimize the squeeze-out that will occur when 
the  threaded  retaining  ring  is  reinstalled  to  hold  the 
stationary base into the recess of the revolving turret. 

 

Figure 24 

 Apply ring of fresh grease for the bearing balls 

Reinstall the Perimeter Bearing Balls 

Use  tweezers  to  carefully  set 

the  3/32”  bearing  balls

 

(there  are  83  of them)  into  the grease  ring (se

Figure 

25

),  placing  the  bearing  balls  as  close  together  as 

possible as you proceed.

 

 

Figure 25 

 Place the bearing balls into the ring of grease 

Reinstall the Threaded Retaining Ring 

Carefully engage  the  threads  of the  threaded  retaining 
ring with the threads in the revolving turret (se

Figure 

26

). 

 

Figure 26 

 Engage the threaded retaining ring 

Use a suitable lens spanner tool (item T3 o

Appendix 1

in  a  pair  of  opposing  tooling  holes  to  tighten  the 
threaded retaining ring

2

 (se

Figure 27

). 

 

Figure 27 

 Tighten the threaded retaining ring 

 

2

 Or use a center punch or nailset tool to snug the threaded retaining ring by placing the 

tip of the tool into one of the four tooling holes and lightly tapping the tool with a small 
hammer or mallet to drive the threaded retaining ring clockwise.   

Содержание BH2-6RE



















Отзывы: