OLT SunShed SSGS1216-FJ-Cedar Скачать руководство пользователя

Страница: 33 / 51

62.

Place 1st

Roof Ridge Cap

on roof peak overhanging shingles

by approximately 1”. Attach with

2 - 1 1/2” Shingle Nails

9” from

end. Place 2nd Ridge Cap 1” back from first cap. Attach with

2 - 1

1/2” Shingle Nails

9” from end. Alternate each Ridge Cap seam as

you proceed.

Parts (Steps 62-63)

Roof Ridge Caps Long x 28

Roof Ridge Caps Short x 1

Hardware (Steps 62-63)

- 1 1/2” Shingle Nails

x 60 total

Alternate Ride Cap seams (offsetting angle cut at peak)

Important:

Butt (thick) end

of Ridge Cap will be facing
towards the outside of shed.

9” from end

Thin End

61.

To further secure roof panels, from the inside, drill 1/8” pilot holes in

each single rafter (3 per rafter) on an angle. Using

3 - 2 1/2” screws

, per

rafter secure rafters to roof plywood.

Note:

from outside, have a helper

push roof panel down so plywood sits flush against rafter when securing.

3 - 2 1/2” angle screwed
into each mid rafter.

Hardware (Step 61)

- 2 1/2” Screws

x 24 total

Mid Rafter

Roof Plywood

4 - 90 degree
Simpson Ties / Gable.

60.

Position

4 - 90° Metal Brackets

onto the roof plywood and

outside Rafter and secure with

4 - 1 1/4” screws each

Complete for both Gables. There are 8 brackets total (4 per side).

Hardware (Step 60)

- 1 1/4” Screws

x 32 total

Y2 - 90° Metal Bracket

x 8 total

4 - 1 1/4” Screws
into each bracket

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 33

Содержание SunShed SSGS1216-FJ-Cedar




















































Результаты поиска

Содержание SunShed SSGS1216-FJ-Cedar

Отзывы:

Похожие инструкции для SunShed SSGS1216-FJ-Cedar

Бренды по названию

Популярные бренды

OLT SunShed SSGS1216-FJ-Cedar, Инструкция по сборке

Результаты поиска

Содержание SunShed SSGS1216-FJ-Cedar

Отзывы:

Похожие инструкции для SunShed SSGS1216-FJ-Cedar

Бренды по названию

Популярные бренды