OLT SunShed SSGS1216-FJ-Cedar Скачать руководство пользователя

Страница: 22 / 51

Parts for One Rafter Section (Polygal Side):

12 - 1 1/2” x 3 1/2” x 80

7/8” - Rafters

2 - 3/4” x 9 1/4” x 91” - Ridge Board
2 - 1/2” x 4 1/2” x 91” - Soffits
12 - 3/4” x 3/4” x 48” - Polygal Support Cleats
4 - 3/4” x 3/4” x 38” - Polygal Support Cleats
* Must complete 2 Rafter Sections

Remaining Rafter Pieces:

4 - 3/4” x 80” x 19 3/4” - Gussets

Important:

Locate all parts necessary to assemble each Rafter Section prior to beginning.

Steps 33-49

to Assemble Rafter Sections. Make sure to complete on a flat, level surface.

Parts for Other Rafter Section (Non-Polygal Side):

12 - 1 1/2” x 3 1/2” x 80

7/8” - Rafters

2 - 3/4” x 9 1/4” x 45 1/2” - Ridge Boards
1 - 3/4” x 9 1/4” x 91” - Ridge Board
2 - 1/2” x 4 1/2” x 68 1/4” - Soffits

C. Rafter Section

Ridge Boards 91” (3)

Ridge Boards 45 1/2” (2)

Gussets (4)

Rafters (24)

Soffits (4)

Ridge Boards Connectors (3)

Polygal Support Cleats
48” (12)
38” (4)

Polygal
Roof Side

33.

Locate

Ridge Boards

and attach together

using

Metal Ridge Board Connectors

and

8 - 3/4” screws

evenly spaced on boards per

connector. Place connector approximately 1 1/4” up
from bottom of

Ridge Board

. Total length when

connected is 182”. Complete two

Ridge Boards

Parts (Steps 33)

Ridge Boards

(3/4” x 9 1/4” x 45 1/2”)

x 2

(3/4” x 9 1/4” x 91”)

x 3

Hardware (Steps 33)

SS2

- 3/4” Screws

x 24

total

Y9 - Metal Ridge

Connector

x3 total

Metal Ridge Board Connector

Ridge Board 91”

Ridge Board 45 1/2”

182”

8 - 3/4” screws

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 22

Содержание SunShed SSGS1216-FJ-Cedar




















































Результаты поиска

Содержание SunShed SSGS1216-FJ-Cedar

Отзывы:

Похожие инструкции для SunShed SSGS1216-FJ-Cedar

Бренды по названию

Популярные бренды

OLT SunShed SSGS1216-FJ-Cedar, Инструкция по сборке

Результаты поиска

Содержание SunShed SSGS1216-FJ-Cedar

Отзывы:

Похожие инструкции для SunShed SSGS1216-FJ-Cedar

Бренды по названию

Популярные бренды