5
1-2 Lift the print head compartment cover by putting your finger in the
notch at its centre, as shown in the figure.
3. Remove the print head from its package and, holding it by the grip,
peel off the film covering the nozzles.
4. Avoid touching the nozzles and the electrical contacts with your
fingers.
5. Place the print head in its seat with the electrical contacts facing
towards the front of the fax machine.
6. Push the print head in the direction indicated by the arrow until it
clicks into place and close the print head compartment cover.
notE
If, after the print head has been installed, the "CHECK PRINT
HEAD" message appears again, try removing it and then
reinserting it, pressing it more firmly into position. If the mes-
sage remains on the display, remove the print head and
clean the electrical contacts of the print head and the car-
riage, see
"To clean the electrical contacts of the print
head"
, section "
Maintenance operations
".
notE
To replace the print head, see the section "
Maintenance
operations
".
A
UTOMATIC
HEAD
NOZZLE
CLEANING
AND
TESTING
PROCEDURE
Once the print head has been inserted
, the fax machine starts
the
nozzle cleaning and checking procedure
, which is com-
pleted by:
• the
printing
, on the sheet loaded automatically, of a diagnostic
test sheet containing:
-
a
numbered scale
, for checking the flow of ink and the
electrical circuits of the print head nozzles.
-
a group of
graphics and text
, so that the printing quality
may be evaluated.
• the display shows the message: "CHECK PRINT OUT",
"1=EXIT 0=REPEAT".
Examine the print test sheet as follows:
• Check that the numbered scale
is not interrupted at any
point
, that the black areas
do not
present any horizontal
white lines
: if these conditions, which confirm that the print
head has been inserted correctly and is working properly, are
respected, set the value
1
. The fax machine returns to its initial
stand-by status and is ready for use.
The display shows the message:
AUTOMATIC RX 00
25-07-01 11:23
• On the other hand, if there are any
interruptions or white
lines
present, set
0
to clean the nozzles again: if the new print
test continues to be unsatisfactory, repeat the procedure an-
other time. Then, if the printing quality does still not meet your
expectations, clean the electrical contacts and the nozzles as
indicated in "
To clean the electrical contacts of the print
head
" and "
To clean the nozzles of the print head
", sec-
tion "
Maintenance operations
".
T
O
SET
IT
UP
FOR
THE
FIRST
TIME
To
get started
on the fax machine, the only setup and installation
parameters you have to set are
the country, the language, the
date and time, your name
and
your telephone number
. The
remaining parameters may be left unchanged (default values) or
changed, to adapt the fax machine to your working requirements
(see "
Setting parameters
").
notE
Once the parameters have been set for the first time,
subse-
quent changes are to be made exclusively as indi-
cated in the procedures described
in "
To set the date
and time and the installation parameters
", section "
More
sophisticated operations
".
notE
As the country
default settings
for each installation param-
eter may be
subject to changes
due to certification re-
quirements or specific users’ needs,
these settings do not
always correspond to those indicated in the manual
: it
is therefore advisable to
print them before changing them
:
Having set the country and the language (see the procedure
described below), press the
key until the display shows:
PRINT OUT:
Press the
key again to confirm.
S
ETTING
PARAMETERS
notE
From here on, if you think you have made a mistake or wish
to abort the procedure in progress during any phase of op-
eration, press the
key.
If
no data is entered for about two minutes
, the fax
machine will
automatically return to its initial stand-by
status.
notE
It is to be borne in mind that the
stand-by status
indicates
that the fax machine is currently
idle
and is the
status
from
which functions may be
programmed
.