Oliver 4910 Скачать руководство пользователя страница 14

 
 
Troubleshooting 

 

Description of Symptoms 

Possible Cause 

Corrective Action 

Machine will not start 

1.  Fuse blown or circuit breaker 

tripped 

2. Cord 

Damaged 

3. Faulty 

switch 

4.  Not connected to power 

source 

5.  No power to machine 
6.  Emergency stop button 

pressed 

1.  Replace fuse or reset circuit 

breaker 

2.  Have cord replaced 
3. Replace 

switch 

4. Check 

connection 

5. Check 

voltage 

6.  Rotate emergency stop button 

clockwise until it pops out 

Blade does not come up to speed 

1.  Cable too light or too long 
2. Low 

current 

3.  Motor not wired for correct 

voltage 

1.  Replace with adequate size 

cable 

2.  Contact local electric 

company 

3.  Refer to motor nameplate for 

correct voltage 

Saw makes unsatisfactory cuts 

1. Dull 

blade 

2.  Blade mounted backwards 
3.  Gum or pitch on blade 
4.  Incorrect blade for cut 

1.  Sharpen or replace blade 
2.  Turn blade around 
3.  Remove blade and clean 
4.  Change blade to correct type 

Material binds blade when ripping 

1.  Fence not aligned with blade 
2. Warped 

wood 

3.  Excessive feed rate 

1.  Check and adjust fence 
2.  Select another piece of wood 
3.  Reduce feed rate. 

Saw vibrates excessively 

1.  Machine not level. 
2.  Damaged saw blade 
3. Bad 

V-belts 

4. Bent 

pulley 

5.  Improper motor mounting 
6. Loose 

hardware 

1.  Reposition on flat, level 

surface 

2.  Replace saw blade 
3. Replace 

V-belts 

4. Replace 

pulley 

5.  Check and adjust motor 
6. Tighten 

hardware 

Material kicked back from blade 

1.  Fence out of alignment. 
2. Dull 

blade 

3.  Carriage height set 

incorrectly. 

4.  Anti-kick back paws dull 

1.  Align fence to chain. 
2. Replace 

blade 

3.  Set carriage height and lock. 
4.  Replace or sharpen anti-kick 

back paws 

Adjustments do not move freely. 

Sawdust and debris in 
mechanisms 

Clean and regrease 

Cut not straight 

Damaged to chain or way due 
to insufficient lubrication 

Replace chain or way. 

Conveyor will not start 

Saw blade not running 

Turn on saw blade 

 

 

14

Содержание 4910















Отзывы: