Oliver 10047VS Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 58

Oliver 10047VS Скачать руководство пользователя страница 27

10047VS Shaper

OLIVERMACHINERY.NET

27

|

Page

To Install Spindle:

1.

Disconnect machine from power source!!

2.

Lock spindle arbor.

3.

Move cutter guard and fence away from the

table opening. Remove table inserts to gain

access of the quill.

4.

Hand thread spindle nut all the way into the

spindle.

5.

Raise arbor all the way up, then lower the

spindle straight into the quill. Hand thread

the entire spindle assembly into the quill.

IMPORTANT:

Take extra care not to cross

thread, or the spindle/quill connection will

be damaged.

6.

Insert spindle draw bar up into the hole at

the bottom of the spindle pulley.

7.

Thread and tighten the draw bar with the

spindle wrench provided. You may also find

a ratcheting wrench useful in tight space.

8.

Tighten the spindle nut with spindle wrench.

Install / Remove Spindle

WARNING

Disconnect machine from power source before installing/removing spindles.

Failure to comply may result in serious injury!

«
...
25
26
27
28
29
...
»

Содержание 10047VS



























































Отзывы:

Нет отзывов