Olimpia splendid Maestro Pro 01925 Скачать руководство пользователя страница 5

Страница: 5 / 42

0.3 - GENERAL WARNINGS

1. This document is restricted in use to the terms of the law and may not be

copied or transferred to third parties without the express authorization of the

manufacturer, OLIMPIA SPLENDID. Our units are subject to change and some parts

may appear different from the ones shown here, without this affecting the text of the

manual in any way.

2. Read this manual carefully before performing any operation (installation,

maintenance, use) and follow the instructions contained in each chapter. Make all

persons involved in the installation of the unit aware of these instructions.

3. THE MANUFACTURER IS NOT RESPONSIBLE FOR DAMAGES TO PERSONS OR

PROPERTY CAUSED BY FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS MANUAL.

4. The manufacturer reserves the right to make any changes it deems

advisable to its models, although the essential features described in this manual

remain the same.

5. The installation and maintenance of units like this one may be hazardous as they

contain refrigerant under pressure as well as powered parts. As such

the

installation,

first startup and

subsequent

maintenance should be carried out exclusively by

qualified personnel.

6. Failing to comply with the instructions contained in this manual, and using the unit

with temperatures exceeding the permissible temperature range will invalidate the

warranty.

Routine maintenance of the filters and general external cleaning can

performed

by the

end user

8. During installation and maintenance, respect the precautions indicated in the

manual, and on the labels applied inside the units. The unit must also be applied

and installed with respect to local and national codes.
9. Always wear gloves and protective goggles when performing any operations on the

refrigeration side of the unit.

10. Units must not be installed in areas containing inflammable gasses, or in very

humid environments (laundries, greenhouses, etc.), or in places where there

equipment will generate unacceptable amounts of heat.

11. Use only original OLIMPIA SPLENDID parts.

WHEN USING ELECTRICAL EQUIPMENT BASIC SAFETY PRECAUTIONS MUST

ALWAYS BE FOLLOWED IN ORDER TO REDUCE RISKS OF FIRE, ELECTRIC

SHOCKS AND INJURY, INCLUDING THE FOLLOWING:

Содержание Maestro Pro 01925











































Результаты поиска

Содержание Maestro Pro 01925

Отзывы:

Похожие инструкции для Maestro Pro 01925

Бренды по названию

Популярные бренды

Olimpia splendid Maestro Pro 01925, Руководство пользователя

Результаты поиска

Содержание Maestro Pro 01925

Отзывы:

Похожие инструкции для Maestro Pro 01925

Бренды по названию

Популярные бренды