OleumTech WG-0900-DH3 Скачать руководство пользователя

Страница: 5 / 104

Page 5

DH3 WIRELESS GATEWAY

USER GUIDE

COMPLIANCES/CONFORMITÉ

English

Important Information to the User

•

This device MUST be professionally installed only by a factory representative or a trained

authorized technician.

•

Changes or modifications not expressly approved by the manufacturer may void the user’s

authority to operate the equipment.

•

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: 1) this device may not cause harmful interference, and 2) this device must

accept any interference received, including interference that may cause undesired

operation.

•

This product contains a FHSS (Frequency Hopping Spread Spectrum) and FSK (Frequency

Shifting Key) modulation RF transceiver for the 902-928 MHz ISM band, designed to meet

FCC 15.247, and is used in industrial control and monitoring applications.

•

To reduce potential radio interference to other users, install and use only the antenna

supplied by the manufacturer to ensure successful communications.

•

The antenna is factory sealed and MUST NOT be modified by the user.

FCC RF Exposure

To comply with FCC RF exposure compliance requirements, a separation distance of at least

20 cm must be maintained between the antenna of this device and all persons.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and if not installed and used in

accordance with the instructions, may cause harmful communications to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the following measures:

•

Reorient or relocate the antenna.

•

Increase the separation between the equipment and receiver.

•

Consult the manufacturer for technical help.

This equipment has been certified to comply with the limits for a class B computing device,

pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables

must be used with this equipment. Operation with non-approved equipment or use of

unshielded cables is likely to result in interference to radio and television reception. The user

is cautioned that changes or modifications made to the equipment without the approval of

the manufacturer could void the user’s authority to operate this equipment.

Содержание WG-0900-DH3









































































































Результаты поиска

Содержание WG-0900-DH3

Отзывы:

Похожие инструкции для WG-0900-DH3

Бренды по названию

Популярные бренды

OleumTech WG-0900-DH3, Руководство пользователя

Результаты поиска

Содержание WG-0900-DH3

Отзывы:

Похожие инструкции для WG-0900-DH3

Бренды по названию

Популярные бренды