manualshive.com logo in svg

Oktober SL1 Homebrewer, Руководство оператора

Поделиться
Скачать
Oktober SL1 Homebrewer Скачать руководство пользователя страница 11

11

Calibration

1. Start by measuring the 1st operation 

seam thickness as described in the seam 

inspection steps. 

 

2. Always start adjustments from a thick-

ness measurement that is too large (For 

instance, .080in for the 1st operation).  

Going too far in with adjustments can 

damage the seaming rollers.  

3. Loosen the first operation adjusting 

nut.  To adjust the seam thickness, 

rotate the adjusting screw OUT (counter 

clockwise) approx. 1 turn for every 

.001in the thickness is too large, then 

re-tighten the nut. For instance, if the 

measurement was .080in, rotate the screw 

OUT 2 rotations to get down to approx. 

.078in

4. Run the 1st operation again, and 

re-measure the 1st operation seam thick-

ness.  Continue adjusting the screw posi-

tion until the 1st operation thickness is 

within specification.

5. Calibration of the 2nd operation is 

the same steps as for the 1st operation.  

Run the operation, measure, and adjust 

the screw as necessary.  

Infeed Adjustment

Содержание SL1 Homebrewer

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды