OKIDATA Microline ML395 Скачать руководство пользователя страница 5

Страница: 5 / 79

Installing/Replacing the Ribbon

1. Make sure printer is turned off.
2. Holding the posts, move printhead to center of platen.

Caution! If you are replacing the ribbon, printhead may be HOT!

3. If you are replacing the ribbon: slide ribbon off printhead posts, remove cartridge from printer, and

discard used cartridge.

4. Unpack ribbon, remove its shipping restraint, and push idler roller latch in.

5. Place ribbon cartridge in printer: pins on either end of car-tridge fit in notches in plates on either

side of printer platen. Push down on cartridge until it clicks into place (see diagram on cartridge).

Note Turn knob in direction of arrow if cartridge does'nt fit into place easily.
5. Thread ribbon around posts as shown, then turn take-up knob clockwise to eliminate ribbon

slack.Making Connections

ML395 ( 96-02-07 )

Содержание Microline ML395
















































































Результаты поиска

Содержание Microline ML395

Отзывы:

Бренды по названию

Популярные бренды

OKIDATA Microline ML395, Руководство пользователя

Результаты поиска

Содержание Microline ML395

Отзывы:

Бренды по названию

Популярные бренды