OHAUS Valor 3000 Скачать руководство пользователя страница 29

Страница: 29 / 52

CHAPTER 4 TESTING

4.5.3 Linearity

Test

This test is used to determine the linearity of the unit throughout its operating range.
The masses used to perform this test can be utility masses.

NOTE:

The scale must pass the Precision and Repeatability Tests, and be calibrated before
the Linearity Test may be performed.

TABLE 4-4. LINEARITY TEST MASSES

Capacity (g)

200 x 0.01

2000 x 0.1

3000 x 1

6000 x 1

300 x 0.2 IP

3000 x 1 IP

6000 x 2 IP

Reference Wt.

500

750

1500

750

1500

Load 1

500

750

1500

750

1500

Load 2

100

1000

1500

3000

150 1500

3000

Load 3

150

1500

2250

4500

225

2250

4500

NOTE:

All masses are nominal values. Be certain to use the same reference mass throughout
the procedure.

1. Place the test mass on the Scale, record the weight and remove.

2. Place Load 1 on the Scale and press TARE.

3. Place the test mass on the Scale, record the weight and remove.

4. Place Load 2 on the Scale and press TARE.

5. Place the test mass on the Scale, record the weight and remove.

6. Place Load 3 on the Scale and press TARE.

7. Place the test mass on the Scale and record the weight.

8. The difference in the weights of the test mass should be within the tolerance in Table

4-1. If not, calibrate (see Appendix A.1) and repeat the test.

9. If the Scale remains out of tolerance, the Load Cell may need to be replaced.

4.5.4 Off-Center

Load

Test

The Off-Center Load Test is used to determine whether displayed weight values are affected by
moving the sample to different areas of the Pan.

1. Place half of the scale’s capacity in the center of the Pan.

2. Note the reading.

3. Move the mass halfway (between the center and the edge) to the front of the Pan.

Note any differences in the displayed weight reading.

4. Repeat the test for the back, left, and right position of the Pan.

5. Maximum allowable change in displayed weight readings for each of the four

positions can be found in Specifications Tables (Chapter 1). If this maximum is
exceeded, follow procedures in Section 4.5.5, Adjusting Off Center Load.

Valor™ 3000 Series Service Manual

4-5

Ohaus Corporation www.ohaus.com

Содержание Valor 3000





















































Результаты поиска

Содержание Valor 3000

Отзывы:

Похожие инструкции для Valor 3000

Бренды по названию

Популярные бренды

OHAUS Valor 3000, Руководство по обслуживанию

Результаты поиска

Содержание Valor 3000

Отзывы:

Похожие инструкции для Valor 3000

Бренды по названию

Популярные бренды