OHAUS Valor 3000 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 52

OHAUS Valor 3000 Скачать руководство пользователя страница 14

CHAPTER 1 GETTING STARTED

1.6 LEGAL FOR TRADE (LFT)

When the scale is set for LFT (on XW and NTEP models), the following menu settings cannot
be accessed/changed: Calibration, Unit, Stability, AST, Filter, Power On Unit, and Global Reset.

To regain access to the locked menu settings, remove the small rectangular LFT/Calibration
Lock Switch cover on the bottom of the scale. (See Figure 1-4.) Use a small flathead screw
driver to move the CAL switch to the left (closer to the “L” in “CAL”), which turns LFT off.

After the LFT/CAL Lock setting has been
turned off, the scale must be inspected in
accordance with local weights and measures
regulations before it can be used in LFT mode
again. Local authorities may apply seals on
the three screws indicated in Figure 1-4.

Figure 1-4. LFT/Cal Lock Switch.

Screws to

which LFT

seals may

be applied

1.6.1 LFT SETUP PROCEDURE

4. Set the Geographical Adjustment Factor (GEO) according to the location where the

scale is to be used. (See Appendix D. Possible values are from 1 to 31.) The
setting is in the Service Menu: press

O/T/Off

and

MODE/UNITMenu

simultaneously

during power on. Press

No

three times until GEO

appears, then press

Yes

. Then

continuously press

No

until the desired number appears. Press

Yes

, then

No

until

END appears. Press

Yes

to return to weighing mode.

5. Access the Setup menu (Press and hold

MODE/UNIT/Menu

until SEtUP appears.

Press

Yes

to enter the displayed menu, or

No

to advance to the next menu, etc.)

Set the following:

Auto Zero Tracking (AZT) = 0.5d

Stability (Stab) =1d

Units as per local LFT requirements

6. Perform an accurate calibration. (See Appendix A.)

7. Turn the Scale off

and disconnect

the AC power connection

.

8. Open the rectangular LFT/Calibration Lock Switch Cover on the bottom of the scale

.

9. Move the switch to the right (closer to the “C” in “CAL”), which turns LFT on.

10. Reinstall the LFT/Calibration Lock Switch Cover.

11. Reconnect the AC power, press

O/T/On/Off

to turn on the scale. During power on,

the display sequence will now include: “LFT.” This message confirms the proper
setting of the LFT mode and the hardware lock switch.

Ohaus Corporation www.ohaus.com

1-6

Valor™ 3000 Series Service Manual

«
...
12
13
14
15
16
...
»

Содержание Valor 3000





















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды