manualshive.com logo in svg

OHAUS CD-31, Инструкция по эксплуатации

Поделиться
Скачать
OHAUS CD-31 Скачать руководство пользователя страница 27

27

CD  Indicators

3.11 Custom  Unit  (Cont.)

Procedure  (Cont.)

• Press 

Enter

 button, SAVED is momementary dis-

played followed by LSD.  There are 6 LSD (least

significant settings you can choose from (see table).

3.12 Menu  Lock-Out  Protection

For type approved Indicators, consult local Weights and
Measures officials to determine sealing method require-
ments.

After the Indicator has been 

set up properly, calibrated

and the 

menus are locked out

 (refer to paragraph 4.1

Calibration), proceed to seal the indicator.

For a lead and wire seal, place the sealing plate into
position and run sealing wire through holes in plastic
retainers.  Run wire through lead seal and crimp closed as
shown.  Alternate LFT paper seal should be positioned
half on the sealing plate and half on the plastic cover.

Indicator Connection Compartment Open

Indicator Connection Compartment Sealed

Access to the

 various menus can be disabled by inserting

the Lock Switch jumper located on the bottom of the
Indicator underneath the Terminal Block.   See figure for
location.  The  Lock Switch jumper when removed, locks
out all menus which have had LOCK turned ON.  The
default setting for the Lock Switch jumper is OFF (jumper
on).

Type  Approved/Legal  for Trade
Indicator  Sealing

All CD-31 and CD-33 Indicators may be sealed for type
approved/legal for trade applications.  A sealing kit is
provided with the Indicator.  The kit includes a lead seal
with wire, screws and cover as shown.

• Press 

Enter

 button, LSD 1 is displayed.

• Press 

 or 

 button and select LSD value.

• Press 

Enter

 button, LOCK is displayed.

• Press 

Enter

 button, LOCK OFF is displayed.

• Press 

 or 

 button and select ON or OFF.

• Press 

Enter

 button, EXIT is displayed.

• Press 

Enter

 button, Indicator returns to weigh mode.

LSD’s

LSD .5

Adds one decimal place
display  counts  by  5’s.

LSD 1

Display  counts  by  1’s.

LSD 2

Display  counts  by  2’s.

LSD 5

Display  counts  by  5’s.

LSD 10

Display  counts  by  10’s.

LSD 100

Display  counts  by  100’s.

Содержание CD-31
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды