manualshive.com logo in svg

OHAUS CD-31, Инструкция по эксплуатации

Поделиться
Скачать
OHAUS CD-31 Скачать руководство пользователя страница 10

10

CD  Indicators

• Plug the AC adapter to an appropriate power supply.  Power is now applied to the Indicator.

• The Indicator performs a self-test. This test is finished when the display indicates WEIGH.

.

2.5 Connecting  Power

Connect the AC Adapter supplied to the connector located at the bottom of the Indicator.  Route the wire from the AC
Adapter through the channel in the bottom of the Indicator.  This will relieve stress on the connector and hold the wire
in place.

2.5.1  Cautionary  Notes

• Models CD-31 and CD-33 Indicators 

must not

 be operated in

 hazardous areas.

• Before connecting the AC adapter, verify that the voltage printed on it corresponds to the local mains

voltage.  If this is not the case, please contact your local Ohaus dealer.

• Model CD-31 and CD-33 Indicators may only be used in a dry environment.

2.5.2  Turning On the Indicator

NOTICE:

The socket/outlet must be installed near

the equipment and shall be easily accessible.

Stabilization

Before initially using the Indicator, allow time for it to adjust to its new environment.  When the CD-31/CD-33 is first
plugged in, the recommended warm up period is five (5) minutes.  The internal circuits of the Indicator are powered
whenever it is plugged into a power source

2.5.3   Power  ON/OFF

The CD-31 and CD-33 Indicators consume minimum power.  The Indicator 

does not

 have an ON/OFF button for power.

It is recommended not to remove power from the Indicator to ensure longer life of the circuitry and display.  If you
desire to use the sleep mode, refer to paragraph 3.2 under Readout for settings.  

NOTE

:  Sleep mode when set on

removes power only from the display after 5 minutes.  Power remains applied to the Indicator at all times when con-
nected to a power source.

Содержание CD-31
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды