OHAUS AV114C Скачать руководство пользователя страница 46

Страница: 46 / 108

3-22

CHAPTER 3 REPAIR PROCEDURES

3.2.8 InCal Motor Removal/Replacement (Cont.)
InCal Motor Replacement (Cont.)

5. Install the InCal Motor to the InCal Mechanism, the motor shaft must be in the position as

shown in Figure 3-28. The InCal Motor shaft must be in the fully counter-clockwise position.

6. Secure the InCal Motor and InCal Motor Shield to the InCal Mechanism with the screws

previously removed.

7. Replace the MFR Load Cell, refer to paragraph 3.2.7.

3.2.9 InCal Mechanism Removal/Replacement
InCal Mechanism Removal

NOTE: Replacement InCal Mechanism's are supplied assembled with the InCal Motor installed.

1. See Figure 3-30 and remove the 3 screws as shown from the InCal Mechanism.

3-Mounting Screws

Figure 3-30. InCal Mechanism Mounting Screws.

Figure 3-31. Removing the InCal Mechanism.

2. See Figure 3-24 and slide the InCal Mechanism to the right to remove

3. See Figure 3-26. Rotate shaft until weight is lowered, then remove the weight.

Содержание AV114C













































































































Результаты поиска

Содержание AV114C

Отзывы:

Похожие инструкции для AV114C

Бренды по названию

Популярные бренды

OHAUS AV114C, Руководство по обслуживанию

Результаты поиска

Содержание AV114C

Отзывы:

Похожие инструкции для AV114C

Бренды по названию

Популярные бренды