OHAUS AV114C Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 108

background image

2-5

CHAPTER 2 DIAGNOSIS

SYMPTOM

Balance can be turned on
but will not calibrate manu-
ally.

PROBABLE CAUSE

Incorrect weights.

Balance is set for legal
for trade operation.
(AV Models only)

Load cell assembly stops
out of adjustment (strain
gauge only).

Load Cell assembly de-
fective.

REMEDY

Verify that proper weights are used.

Check that LFT lock switch is set to un-
locked position.

Set the Setup Menu Legal for Trade set-
ting to Off.

Set the Lockout Menu CAL to Off position.

Calibrate the balance using procedure in
Appendix A Calibration, perform both Lin-
earity and Span calibrations.

If the balance fails to calibrate properly,
enter the service mode Appendix B and
perform a Linearity and Span calibration
again. If this fails either the load cell is
defective and will require replacement or
the load cell adjustment stops have loos-
ened and have to be reset.
Perform ->Repair Procedures 3.1.1or
3.2.1 and open the balance.

Remove the cover from the load cell.
Check the up-down stops in accordance
with section 4.4 and refer to table 4-5.
Measure the gap settings, if OK, the load
cell is defective. Perform ->Repair Proce-
dures 3.1.5 or 3.2.5

If the up stop and down stop adjustments
were set incorrectly, perform procedures
in section 4.2.1 or 4.3.1 and reassemble
and calibrate the balance. if the balance
fails to calibrate, the load cell is defective.
Perform ->Repair Procedures 3.1.5 or
3.2.5

TABLE 2-5 BALANCE CANNOT CALIBRATE MANUALLY

«
...
19
20
21
22
23
...
»

Содержание AV114C













































































































Отзывы:

Нет отзывов

Похожие инструкции для AV114C

valor 5000 series

Бренд: OHAUS Страницы: 56

Бренд: OHAUS Страницы: 196

DEFENDER SERIES

Бренд: OHAUS Страницы: 64

Бренд: OHAUS Страницы: 4

Nutri-Weigh Slim

Бренд: Salter Страницы: 13

Бренд: Salter Brecknell Страницы: 2

Бренд: J-Scale Страницы: 2

Бренд: Rice Lake Страницы: 69

Бренд: Inscale Страницы: 20

Бренд: G&G Страницы: 18

Бренд: Setra Systems Страницы: 32

Бренд: Gamry Страницы: 35

Бренд: CAS Scale Страницы: 60

Бренд: Saturn Страницы: 13

Бренд: OHAUS Страницы: 64

Бренд: OHAUS Страницы: 32

Бренд: ISHTAA Страницы: 8

Бренд: B-TEK Scales Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды