manualshive.com logo in svg

OHAUS AV114C, Руководство по обслуживанию

Поделиться
Скачать
OHAUS AV114C Скачать руководство пользователя страница 40

3-16

CHAPTER 3 REPAIR PROCEDURES

3.2.6 Strain Gauge Calibration InCal Mechanism Removal/Replacement (Cont.)

Motor Removal (Cont.)

2. Refer to Figure 3-15  and lift the Motor up from the InCal Mechanism just enough to

disengauge the Timing Belt.

3. Refer to Figure 3-16 and slide the Timing Belt off of the Top Gear and remove the Top Gear.

Lift Motor

Timing Belt

Figure 3-15. Disengauge Timing Belt.

Top Gear

Slide Timing Belt

off of Timing Gear

Figure 3-16. Removing Top Gear.

4. Refer to Figure 3-17 which illustrates the top

Gear removed, the Motor can now be re-

moved from the InCal Mechanism.

Motor Installation

1. Install the replacement Motor into position

with the Timing Belt as shown in Figure 3-17.

2. Slide on the Top Gear as shown in Figure

3-16.

3. Refer to Figure 3-15, lift the Motor slightly and

position the Timing Belt on the Top Gear as
shown.

4. Refer to Figure 3-18, rotate the Top Gear

until it  is in the position as shown while
holding the Motor in place.

Figure 3-17. Top Gear Removed.

Remove Motor

Gear Removed

Figure 3-18. Top Gear Alignment.

Align Top Gear

Содержание AV114C













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды