Ogura HCC-16DF Скачать руководство пользователя страница 6

Страница: 6 / 16

Names of the parts

■

Standard accessories (HCC-16DF)

Battery charger (DC18RA) ---------------------------- 1
Battery (BL1830) ----------------------------------------- 1
Battery cover ---------------------------------------------- 1
Hex wrenches (M3,M4,M5,M6) ---------- One each
Spanner (14 mm

17 mm) --------------------------- 1

Hydraulic oil #46 (35 cm

) ----------------------------- 1

Carrying case --------------------------------------------- 1

Type of spare blade and detachment

Model

A (attached on the Bar Holder side.)

B (attached on the Cutter Rod side.)

HCC-16DF (Ø 3 ~ 16)

9 mm , two holes M5

8 mm, two holes M5

HCC-19DF (Ø 3 ~ 20)

11.5 mm , two holes M6

10 mm, two holes M5

■

Standard accessories (HCC-19DF)

19 mm) --------------------------- 1

Hydraulic oil #46 (150 cm

) --------------------------- 1

Carrying case --------------------------------------------- 1

Spare blade size

❇

Attach the blade corresponding to the model correctly.

Note: Use only genuine Ogura blades.

Blade B on Cutter Rod

Blade A on Bar Holder

Spare Blades

Securing bolts should be
firmly tightened.
Confirm periodically that
the blade is tightened
properly.

Battery (BL1830)

Charger (DC18RA)

Содержание HCC-16DF

















Результаты поиска

Содержание HCC-16DF

Отзывы:

Бренды по названию

Популярные бренды

Ogura HCC-16DF, Инструкция по эксплуатации

Результаты поиска

Содержание HCC-16DF

Отзывы:

Бренды по названию

Популярные бренды