background image

User’s Manual     Wireless Module         

Page 1 of 22 

 

 

FCC Statement 

Federal Communication Commission Interference Statement 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 

residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful 

Interference to radio communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of 

the following measures: 

- Reorient or relocate the receiving antenna. 

- Increase the separation between the equipment and receiver. 

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

- Consult the dealer or an experienced radio/TV technician for help. 

 

IMPORTANT NOTE: 

 

Any changes or modification to this unit not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment. 

 

FCC RF RADIATION EXPOSURE STATEMENT: 

This module must be installed and operated in accordance with provided instructions and the antenna used for this 

transmitter must be installed to provied a separation distance of at least 20 cm from all persons and must not be 

co-located or operating in conjunction with any other antenna or transmitter. End-uses and installers must be provide 

with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. 

LABELING REQUIREMENTS:   

1.

 

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions (1) 

this device may not cause harmful interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation. 

 

2.

 

Host device of OEM integrator must be labeled with: 

  CONTAINS TX FCC ID: QR4WF5370M08 

INFORMATION FOR THE OEM INTEGRATORS: 

The following statements must be included with all versions of this document supplied to an OEM or integrator, 

Содержание GWF-3M08






















Отзывы: