manualshive.com logo in svg

OfiTE 170-181, Инструкция по эксплуатации, Страница: 6 / 34

Поделиться
Скачать
OfiTE 170-181 Скачать руководство пользователя страница 6

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

5

#170-181-S  Test Cell, Stainless Steel (For Mud Testing)

#120-910-028 

O-ring for Rupture Disk, Viton 75D, Qty: 1

#130-81-040 

Retaining Ring, Qty: 2

#165-44-2 

Anti Seize Compound, Silver, 7g Pouch, Qty: 4

#170-13-3 

O-ring for Cell, Viton 75D, Qty: 4

#170-16 

Valve Stem, Qty: 2

#170-17 

O-ring for Valve Stem, Viton 75D, Qty: 4

#170-18 

Cement Screen, Qty: 2

#170-180-020-S  Cell Body, 175 mL, Qty: 1

#171-190-023 

Locking Ring, Qty: 2

#171-190-027 

Rupture Disk, Qty: 1

#171-190-029 

Cap Wrench, Qty: 1

#171-190-032-S  Cell Cap, Outlet, Cement, Qty: 1

#171-190-033-S  Cell Cap, Inlet, Cement, Qty: 1

#171-190-057 

O-ring for Valve Stem, Viton 90D, Qty: 4

#171-190-058 

O-ring for Rupture Disk, Viton 90D, Qty: 1

#171-190-060 

O-ring for Cell, Viton 90D, Qty: 4

#170-00-1  Heating Jacket, 115 Volt:

#170-01-1  Heating Jacket, 230 Volt:

#164-32 

Male Connector for Power Cable (230 Volt) 

 

#170-05 

Thermostat for HTHP Filter Press 50-500

#170-10 

Thermostat Pilot Light

#170-11 

Heating Element, 200W, Qty: 2

#170-15 

Base

#170-21 

Stand

#170-30 

Stainless Steel Thermostat Cover

#170-44 

Rubber Foot ½", Qty: 4

#171-32 

Midget Knob

#171-82 

Power Cord with Male Plug, 8' (115 Volt)

Optional:

#143-05 

CO

2

 Bulbs, 8-Gram, Package of 10, UN 1013

#152-00 

Hamilton Beach Mixer, With Container

#152-01 

Armature For Model 936 H.B. Mixer, 115 Volt

#155-20 

Timer; 60 Min. Interval

#170-03 

Carrying Case, Stainless Steel 

#170-13 

O-ring for Test Cell, NBR/Nitrile (Buna N), For temperatures up 

to 250°F (121°C)

#170-13-4  O-ring for Test Cell, Perfluorocarbon (FFKM), For temperatures 

up to 500°F (260°C)

#170-13-5  O-ring for Test Cell, Ethylene propylene (EPM/EPDM), For tem

-

peratures up to 400°F (204.4°C), Water-based fluids only

#170-33 

HTHP Cell Cap Puller

#170-40 

Test Cell Removal and Carrying Tool

#170-91 

HTHP Pressure Relief Tool

#170-92 

Safety Clamp for HTHP Fluid Loss Cells

Содержание 170-181



































Отзывы:

Нет отзывов