manualshive.com logo in svg

OfiTE 170-181, Инструкция по эксплуатации, Страница: 30 / 34

Поделиться
Скачать
OfiTE 170-181 Скачать руководство пользователя страница 30

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

29

4. 

Regulator and Manifold Maintenance:

a. 

Replace both o-rings on the puncture pin (#143-02-13 and #143-02-

14) at least once a year.

b. 

Regulator loses pressure or steadily increases in pressure – Replace 

the seat assembly and diaphragm.

Concoa Repair Kit – Part #143-07. Normally the Concoa regulator is sup

-

plied with the 175 mL models

The Large High Pressure Concoa Regulator (805-1140) and the smaller 

Concoa Regulator (805-1179) both take the same Regulator Repair Kit 

Always replace (order separately) the rubber diaphragm, #143-00-1, 

which is not supplied with the #143-07 kit.

200-psi Gauge

(#143-01)

#142-10 - CO

2

 Pressuring Assembly

Safety Bleeder Valve

(#143-06)

Regulator (#143-00)

CO

2

 Puncture Head

Assembly (#143-02-10)

CO

2

 Cartridge

(#143-02-05)

Barrel for CO

2

Cartridge (#143-03)

CO

2

 Puncture Head

Assembly (#143-02-10)

CO

2

 Puncture Head

Assembly (#143-02-10)

Puncture Pin Holder

Assembly (#143-02-11)

O-ring

(#143-02-14)

O-ring

(#143-02-13)

Diaphragm

(#143-00-1)

Repair Kit

(#143-00-1)

Содержание 170-181



































Отзывы:

Нет отзывов