manualshive.com logo in svg

OfiTE 170-181, Инструкция по эксплуатации, Страница: 31 / 34

Поделиться
Скачать
OfiTE 170-181 Скачать руководство пользователя страница 31

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

30

To replace the Seat Assembly

1. 

Unscrew the spring case (housing cover). This may require a strap 

wrench.

2. 

Remove the spring case.

3.  Remove the rubber diaphragm (#143-00-1) from inside the spring case.

4. 

Remove the thrust plate (#143-00-7).

5. 

Using a wrench, loosen and remove the brass colored retainer.

6.  The thrust pin and seat are now exposed and can be removed from the 

base.

7. 

Replace the spring – repair kit.

8. 

Replace the seat holder – repair kit.

9.  Replace the thrust pin and the Teflon seat which can be attached before 

insertion-repair kit.

10. 

Replace the brass retainer and tighten with a wrench.

11. 

Replace the thrust plate with the curved edges downward.

12. 

Place a new rubber diaphragm inside the Soring case

13. Replace the spring case and hand tighten.

Power Cord

1. 

Check power cord for insulation wear and loose connections near the 

heating jacket and plug.

2. 

The heating jacket should be placed no farther than the distance of the 

power cord from an electrical outlet.

3.  The power cord should be kept away from the hot surface of the heating 

jacket, while in use.

Any customer installed wiring, power cords or electrical connectors will 

Void All Warranties.

Storage Space

1. 

Consumables and tools should all be kept in one dedicated place.

2. 

Components, such as manifold assemblies should be kept in a similar 

dedicated place.

Содержание 170-181



































Отзывы:

Нет отзывов