OfiTE 170-181 Скачать руководство пользователя страница 34

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

33

Warranty and 

Return Policy

Warranty:

OFI Testing Equipment, Inc. (OFITE) warrants that the products shall be free from liens and defects in 

title, and shall conform in all respects to the terms of the sales order and the specifications applicable to 

the products. All products shall be furnished subject to OFITE’s standard manufacturing variations and 

practices. Unless the warranty period is otherwise extended in writing, the following warranty shall apply: 

if, at any time prior to twelve (12) months from the date of invoice, the products, or any part thereof, do not 

conform to these warranties or to the specifications applicable thereto, and OFITE is so notified in writing 

upon discovery, OFITE shall promptly repair or replace the defective products. Notwithstanding the forego

-

ing, OFITE’s warranty obligations shall not extend to any use by the buyer of the products in conditions 

more severe than OFITE’s recommendations, nor to any defects which were visually observable by the 

buyer but which are not promptly brought to OFITE’s attention.

In the event that the buyer has purchased installation and commissioning services on applicable products, 

the above warranty shall extend for an additional period of twelve (12) months from the date of the original 

warranty expiration for such products.

In the event that OFITE is requested to provide customized research and development for the buyer, 

OFITE shall use its best efforts but makes no guarantees to the buyer that any products will be provided.

OFITE makes no other warranties or guarantees to the buyer, either express or implied, and the warranties 

provided in this clause shall be exclusive of any other warranties including ANY IMPLIED OR STATUTORY 

WARRANTIES OF FITNESS FOR PURPOSE, MERCHANTABILITY, AND OTHER STATUTORY REM

-

EDIES WHICH ARE WAIVED.

This limited warranty does not cover any losses or damages that occur as a result of:

• 

Improper installation or maintenance of the products

• 

Misuse

• 

Neglect

• 

Adjustment by non-authorized sources

• 

Improper environment

• 

Excessive or inadequate heating or air conditioning or electrical power failures, surges, or other 

irregularities

• 

Equipment, products, or material not manufactured by OFITE

• 

Firmware or hardware that have been modified or altered by a third party

• 

Consumable parts (bearings, accessories, etc.)

Returns and Repairs:

Items being returned must be carefully packaged to prevent damage in shipment and insured against pos

-

sible damage or loss. OFITE will not be responsible for equipment damaged due to insufficient packaging. 

Any non-defective items returned to OFITE within ninety (90) days of invoice are subject to a 15% restock

-

ing fee. Items returned must be received by OFITE in original condition for it to be accepted. Reagents and 

special order items will not be accepted for return or refund.

OFITE employs experienced personnel to service and repair equipment manufactured by us, as well as 

other companies. To help expedite the repair process, please include a repair form with all equipment sent 

to OFITE for repair. Be sure to include your name, company name, phone number, email address, detailed 

description of work to be done, purchase order number, and a shipping address for returning the equip

-

ment. All repairs performed as “repair as needed” are subject to the ninety (90) day limited warranty. All 

“Certified Repairs” are subject to the twelve (12) month limited warranty.

Returns and potential warranty repairs require a Return Material Authorization (RMA) number. An RMA 

form is available from your sales or service representative.

Please ship all equipment (with the RMA number for returns or warranty repairs) to the following address: 

OFI Testing Equipment, Inc. 

 

Attn: Repair Department 

 

11302 Steeplecrest Dr. 

 

Houston, TX 77065

 

USA 

OFITE also offers competitive service contracts for repairing and/or maintaining your lab equipment, in

-

cluding equipment from other manufacturers. For more information about our technical support and repair 

services, please contact [email protected]

.

Содержание 170-181



































Отзывы: