background image

MAINTENANCE AND CARE 
 
 

Visual Inspection 

a)  Smooth safety and trigger movement. 
b)  All screws are tightened. 
c)  Never use damaged or incomplete tool. 

 

Cleaning 
The periodical cleaning of the tool is recommended to ensure proper functioning. 

a)  Disconnect the tool from the air supply. 
b)  Remove all fasteners 
c)  Clear the magazine and nose sections with a blowgun to remove any accumulated debris. 
d)  Check for free movement of the trigger, follower and work contact element. Remove any 

obstructions carefully. 

e)  Oil tool daily with proper air tool oil. 
f)  Empty the air tanks on your compressor daily to prevent moisture buildup in the air lines. 

 

Lubrication 
The tool should be lubricated daily.  

a)  Add a few drops of non-detergent oil in the tool air inlet before each use. 
b)  Never use detergent oils, which can damage o-rings causing the tool to malfunction. 
c)  Wipe off excessive oil from the exhaust. 
d)  Hammer cage set should be periodically lubricated 

– at least one time per month 

Excessive oil will damage o-rings of tool. 

 

 

 

 
 
 
 
 
 
 
 

 

 
 

WARNING:  

Stop using the tool immediately if any of the following problems occurs. Serious personal injury could 
occur. Necessary repair of replacement must be carried out by qualified and trained technician of an 
authorized service location.  

 
 
OEM Limited One Year Warranty 

For one (1) year from the date of purchase OEM tools will warranty this tool against defects in materials 
and workmanship. Defective OEM brand hand tools purchased from an authorized OEM distributor will be 
repaired or replaced when returned freight prepaid to the OEM Warranty Dept., 3580 E. Raines Rd. #3, 
Memphis, TN 38118. Proof of purchase with date of purchase will be required with all returns. OEM will 
not be responsible for any consequential or incidental damages arising from the breach of this or any 
other warranty, whether expressed, implied or statutory. Some states do not allow the exclusion or 
limitation of consequential or incidental damages, so the above exclusion may not apply to you. This 
warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 

Содержание 24402









Отзывы: