Oce Arizona 6160 XTS Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 180

background image

UV Curing System

Chapter 2

‐

Safety Information

17

Océ Arizona 6100 Series

UV Curing System

Introduction

The UV Curing System  on the  Océ Arizona printers generates  hazardous levels of  thermal,
electrical and  UV energies. UV-curable ink  need a  high energy level of  UV light to  cure. The UV
curing system  is  made up of two  mercury arc  lamps attached to the  carriage.

How to Handle UV Lamps:

UV lamps operate at high temperatures. Never touch a lamp in

operation. Let the  lamps cool  for  a  minimum of five minutes before attempting any  maintenance.
Use  extreme care in  handling the UV lamp bulbs. The UV bulbs contain a  small amount  of metallic
mercury which is toxic  when ingested, handled, or  breathed. Therefore, if bulbs are  broken, care
should be  taken to  clean up the  spill immediately, and  then  disposed  of  according to  local
regulations concerning Mercury disposal.

UV Lamp Hazards

: Superficial eye damage and burning of the skin can occur with even brief

exposure to UV light.  Serious injuries can result from prolonged exposure, especially if
unshielded. Special restrictions and protective measures  are essential when the printers are used.
Wear Industrial Protective Eyewear with lenses that block both UVA and UVB. Gloves and  long-
sleeved work  clothes are  essential to  reduce the skin's exposure to UV emissions.

Bare skin contact with the UV lamp bulbs must be avoided. When heated, compounds from the
skin can form permanent etching on the surface of the UV bulb. A contaminated bulb may fail
prematurely.

Ozone:

As a UV lamp warms up, it briefly passes through a section of the light spectrum which

excites oxygen molecules enough to create ozone. Once a UV lamp has completely warmed up,
only very minute amounts of ozone are present.

NOTE

A high concentration of ozone can cause irritation, headaches or nausea. Provide adequate
ventilation as indicated in the Site Preparation Guide.

CAUTION

Warning for Seated Individuals: UV emissions are highest at a height of 90 cm (35 inches) above

the floor. This can be an issue for individuals seated near the printer.Remove all chairs within 5

meters (16 feet) of the printer.

WARNING

One or more lamp(s) inside this product contain Mercury. Dispose these lamp(s) according to all

federal, state and local regulations.

Mercury containing lamp(s) must be removed and treated separately according Directive

2012/19/EU (Waste Electrical and Electronic Equipment). European Waste Catalogue (EWC)

number of the mercury containing fluorescent lamp: 20 01 12.

Personal Safety

WARNING

UV Light Emissions can be harmful:

«
...
15
16
17
18
19
...
»

Содержание Arizona 6160 XTS





















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arizona 6160 XTS

Бренд: Oki Страницы: 282

Бренд: MakerPi Страницы: 21

Aficio SP C420DN

Бренд: Ricoh Страницы: 4

Бренд: SEWOO Страницы: 17

Бренд: Parkside Страницы: 176

Бренд: A&D Страницы: 32

Phaser 3100MFP/S

Бренд: Xerox Страницы: 56

PcOS Series 80PLUS

Бренд: Ithaca Страницы: 131

imagePROGRAF iPF670E

Бренд: Canon Страницы: 6

imagePROGRAF iPF 655

Бренд: Canon Страницы: 2

imagePROGRAF PRO 1000

Бренд: Canon Страницы: 17

imagePROGRAF iPF8400S

Бренд: Canon Страницы: 38

imagePROGRAF SD-22

Бренд: Canon Страницы: 14

imagePROGRAF PRO-2100

Бренд: Canon Страницы: 65

imagePROGRAF MFP

Бренд: Canon Страницы: 4

imagePROGRAF iPF700 with Colortrac Scanning System

Бренд: Canon Страницы: 10

imagePROGRAF iPF 755

Бренд: Canon Страницы: 2

imagePROGRAF TA-20

Бренд: Canon Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды