Possible troublesomes on high intensity part number 113780
To be used in the manual:
figure 3-4 page 23 for the localization of each items inside the power supply of each flash-head
figure 3-6 page 28 for the internal wiring of the power supply of each flash-head
figure 3-7 page 29 for the internal wiring of the controller
figure 2-1 page 16 for the visual indicators on the command card
Possible troublesomes
Action
Solution
Red power control indicator (
as
shown in figure 3-6 page 28)
for
voltage presence is off
As per figure 3-6 page 28:
Check input voltage 230VAC
between the terminals 1 and 2 on the main terminal
connection TB1, and the switch position and the status of the
surge protection.
Replace the defective part (surge
protection
DS215-230/G part
number 451721
or switch position)
if necessary
D15 is off on the command card
(as
per figure 2-1 page 16)
230VAC is present but the light does
not work.
As per figure 3-6 page 28:
Check the presence of the 48Vdc
voltage on the 2 outputs of power supplies part number
113742 and the status of their fuse
Replace the power supply part
number 113742 or the fuse if
necessary
The light works permanently on day
mode, twilight mode or night mode
Check if S1 is on « remote». Or check the wires coming from
the controller on the terminals 3 and 4 of TB1 to the relay and
up to the 2 command board part number 113944(HI)L and
113944(HI)R.
Put S1 in “test mode”:
When S2 in night mode, the relay 3 must be lighted
When S2 is in day mode, the relay 4 must be lighted
When S2 is in twilight mode, all relays should be off
Tighten the terminals on TB1, on
the relay. Replace a 48Vdc relay if
necessary
Some indicators D6 to D12 are red
blinking on the command card
(as
per figure 2-1 page 16)
One led projector (or more) does not
work
Tighten the wires of each led projector inside the stainless
cabinet
Otherwise tighten the green terminals of the 8 power cards
(total 16 wires “-“) and terminals 1 to4 on TB2 (total 4 wires
“+”)
Otherwise check the power card and their projector according
to the
procedure below*
Replace power card part number
113741B or projector part number
113761-4 if necessary
D13 is blinking and D14 is off on the
command card
(as per figure 2-1
page 16)
The flashes of the light is not
synchronized with the other lights
and it flashes at 15 pulse per minute
The top sync is not received from the controller.
Check the wires connection from the controller on terminals
11 of TB1
as per figure 3-7 page 29
to the 2 command cards
in the power supply of flash-head on TB1 7 as
per figure 3-6
page 28
Replace the command card part
number 113744L and/or 113744R
in the power supply of the flash-
head if necessary
The flashes of all lights are not
synchronized
The top sync of the controller is not send or not received by
the lights.
Check the wires connection from the controller on terminal
11 of TB1
as per figure 3-7 page 29
, to the power supply of
each flash-head
Replace the command card part
number 113744 in the controller if
necessary
The light does not send any alarm to
the controller in case of default
Check the wires connection from the controller on the
terminal 10 on TB1 a
s per figure 3-7 page 29
up to the power
supply of the light terminal 6 on TB1 a
s per figure 3-6 page
28
Check that the light number that has been assigned is unique
on the fault transmitter card
Replace the fault transmitter card
part number 113749B if necessary
All lights work in day/twilight/night
mode permanently
Check the controller is on « remote» position. Otherwise
check the position of the photocell (in the North in the North
Hemisphere), the wiring of the photocell and test the photocell
by masking it with your hand
Replace photocell part number
113135 or the controller if
necessary
Otherwise call the manufacturer
*: One p
rojector not working
For example if luminous indicator D7 (or WHITE#2) is red blinking, disconnect the green terminal from its power card and plug it to the
power card for example D8 (or WHITE#3) close to it.
- If the luminous indicator D8 does blink also, it means the projector is defective
- If the luminous indicator D8 does not blink, it means the projector is ok but the power card linked to WHITE#2 is defective
1
Содержание OFP-CAB-8E-RW-240-HIA
