background image

P1PV / P1PVCD Series 

Installation & Service Instructions 

 

 
 

 

 

030099-347 Rev. 2 

pg 16 of 16  

         © Copyright 2007 OASIS Corporation 

 

Allow this water to empty into an open bucket 

 

Remove the hot tank from the cooler as follows: 

o

 

Disconnect earth wire from column support 

o

 

Disconnect live & neutral wires from hot tank switch and heat limiter 

o

 

Disconnect vent pipe from front panel 

o

 

Disconnect outlet pipe from water outlet assembly 

o

 

Support the tank while removing the two screws attaching the tank to the shelf 

o

 

Withdraw the tank from the column support 

 

Temporarily plug the vent and hot tank outlet 

 

Prepare a descaling solution by mixing 125 grams of citric acid crystals with one litre of very 
hot water.  (Wearing rubber gloves is recommended )

 

 

Turn the hot tank upside down and pour the descaling solution into the hot tank inlet tube 
using a funnel

 

 

 

Let the unit stand for at least twenty minutes.

 

 

Drain the descaling solution through the hot tank inlet tube

 

 

Replace the hot tank and rebuild the cooler

 

 

Reconnect the cooler to the mains supply

 

 

Drain at least 5 litres of hot  water from the outlet before switching on the hot tank

 

 
 
 
 

THIS APPLIANCE MUST BE EARTHED. 

This appliance is not suitable for unsupervised use by young children or aged and infirm persons. The warranty, 

Underwriter’s Laboratory certification and CE certification for this machine are automatically void if any alteration, 

modification, or combination with any other machine or device is deemed to be the source of any claim. The UL and CE 

certification may be void as the result of any alteration or modification. The manufacturer accepts no liability resulting from 

any alteration, modification, or combination with any other machine or device. 

 

EXCEPT AS SET FORTH HEREIN, THE MANUFACTURER MAKES NO OTHER WARRANTY, GUARANTEE, 

OR AGREEMENT EXPRESSED, IMPLIED OR STATUTORY, INCLUDING ANY IMPLIED WARRANTY OR 

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 

 

Manufacturing location: 

Europe 

 

OASIS East Sp.z o.o. 

Gutenberga 20 str 

44-164 Gliwice SEZ, Poland 

Tel:   +48 32 332 6501   ;   Fax:  +48 32 332 6500 

www.oasis.ie

 

 
 

In North America, contact: 

 

TRI PALM INTERNATIONAL, LLC 

222 East Campus View Blvd. • Columbus, OH  43235 U.S.A. 

1-800-64-OASIS (1-800-646-2747) 

www.oasiswatercoolers.com

 

 

 

Содержание P1PV Series

















Отзывы: