Oasis Aquatics SmartChem Скачать руководство пользователя страница 18

Oasis SmartChem - INSTALLATION AND OPERATION MANUAL 

 

 

 

 

 

 

Page 

17

 of 

22

 

 

Chlorine is too Low 

Filter run time/s aren’t sufficiently long enough or Chlorinator output isn’t 
high enough  
Lengthen  filter  run  time/s  or  increase  Chlorinator  output.  Make  sure 
Chlorinator is working. 
Filter requires a back wash   
Back wash filter. 
Stabiliser (Sun Block) level is too Low (Outdoor Pools)  
Adjust level of Stabiliser to appropriate level 

Note: The need to run Stabiliser in an outdoor pool may be reduced 
if your Chlorinator is sufficiently sized to produce enough chlorine 
to negate the use of Stabiliser, ie the bigger the chlorinator the lower 
the stabiliser level needs to be. 

pH level is too high  

–  Adjust pH level to correct level (7.2 – 7.8). 

ORP probe not reading correctly  -  Clean and or Re-calibrate probe or 
adjust probe Offset (as per pg 8). 
ORP Set Point is set to Low  -  Adjust ORP Set Point to appropriate level, 
700mV. 

Chlorine is too high  

pH level is too high   
Adjust pH level to correct level (7.2 

– 7.8). 

Total Dissolved Solid levels are too high   
The only way to decrease the Total Dissolved Solids (<1500ppm) level of 
your pool is to introduce fresh water to dilute the pool water. Give your 
Filter a really long backwash to drop the level of your pool (by the amount 
recommended by your pool shop) and re-fill with fresh water. 
Stabiliser (Sun Block) level is too High (Outdoor Pools)   
Adjust level of Stabiliser to appropriate level (30-50mg/L). As per above. 

Note: The need to run Stabiliser in an outdoor pool may be reduced 
if your Chlorinator is sufficiently sized to produce enough chlorine 
to negate the use of Stabiliser, ie the bigger the chlorinator the lower 
the stabiliser level needs to be. 

ORP probe not reading correctly  -  Clean and or Re-calibrate probe or 
adjust probe Offset (as per pg8). 
ORP Set Point is set to High  -  Adjust ORP Set Point to appropriate level, 
700mV. 
Manual Overdosing of Chlorine (Shock Treatment)  -  Maintain ORP Set 
Point. It may take a period of days  to weeks or the ORP reading to drop 
back to normal levels. This depends on how large the Overdose (shock 
treatment) was. The 

Oasis SmartChem 

will not continue adding chlorine 

during this time period. 

 

DISCLAIMER

:  Information  in  this  guide  is  intended  to  provide  general  information  on  a  particular 

subject(s)  in  good  faith and  is  not  an  exhaustive  treatment  of  such  subject(s). Its  use  is  beyond  the 
control of the author, contributor, publishers, licenced professionals and under no circumstances should 
the guide be used as a substitute for such professionals. No representations or warranties are made 
that the content, advice and recommendations in this guide are current, free from errors or omissions, 
or appropriate for the user’s circumstances or abilities. No liability or responsibility is accepted persons 
or 

OASIS  AQUATICS  Pty  Ltd

  appointed  agents. 

OASIS  AQUATICS  Pty  Ltd 

reserves  the  right  to 

refuse warranty if any damage caused to the chlorinator or auxiliary pool equipment that is not a result 
of a manufacturer’s defect. 

 

Содержание SmartChem


























Отзывы: