NXP Semiconductors PN544 C2 Скачать руководство пользователя страница 155

Страница: 155 / 172

NXP Semiconductors

UM191812

PN544 C2 User Manual

191812

All information provided in this document is subject to legal disclaimers.

User Manual

Rev. 1.2 — 2010-06-16

155 of 172

Address Name

Comment

Default

0x9898

IRQ_Config

- Bit 5 : 0 ... IRQ logical level is active HIGH (Default value)

1 ... IRQ logical level is active LOW

- Other Bits : RFU (keep unchanged)

0x02

0x9899

GPIO_Config_PEN

Gpio default configuration: PEN (Port Enable)

Each bit in the configuration register represents the GPIO pin with the
corresponding number

If set to 1, and if the corresponding PDIR is set to 0, the corresponding
GPIO is configured in input

0x00

0x9E71

PlClockRequest

Indicates how the clock is requested to the host by the PN544.

- 0x00 -> no request

- 0x01 -> request through CLKREQ pin (GPIO pin 2 set to high when
clock requested, HighZ unless, whatever GPIO default configuration)

- 0x02 -> request through NXP_EVT_CLK_REQUEST event

- Others values are RFU

0x00

0x9E72

PlClockAck

Indicates how the clock request is acknowledged by the host. Clock
acknowledgment is only valid in case of Clock request mechanism
enabled (see NXP_PlClockRequest).

- 0x00 -> acknowledged thanks to timeout (see PlClockTimeout)

- 0x01 -> acknowledged through CLKACK pin (GPIO pin 1)

- 0x02 -> acknowledged through NXP_EVT_CLK_ACK event

- Others values are RFU

0x00

0x9E6F

PlClockTimeout

Indicates the timeout value to be used for clock request acknowledgment
(up to 255ms in 1ms steps).

Recommended value is 10 ms or less.

0x0A

0x9E74

PlRfLowPower

- Bits 0 to 2: Sensitivity of the RF Low Power Mode (value between 0 and
6, 0 -> sensitivity maximal, 6 -> sensitivity minimal)

- Bits 3 to 6 are RFU

- Bit 7: use of the RF Low Power Mode (0 -> not used, 1 -> used)

0x00

Содержание PN544 C2













































































































































































Результаты поиска

Содержание PN544 C2

Отзывы:

NXP Semiconductors PN544 C2, Руководство пользователя, Страница: 155 / 172

Результаты поиска

Содержание PN544 C2

Отзывы: