NXP Semiconductors PN544 C2 Скачать руководство пользователя страница 154

Страница: 154 / 172

NXP Semiconductors

UM191812

PN544 C2 User Manual

191812

All information provided in this document is subject to legal disclaimers.

User Manual

Rev. 1.2 — 2010-06-16

154 of 172

Address Name

Comment

Default

0x9808

AST-ANT1-ANT2

Antenna Self Test: default PBF (4

parameter)

0xFF

0x989D

AST-GSP2

Antenna Self Test: GSP for TX2

0x27

0x989E

AST_Current

Antenna Self Test: Current start threshold

0x3F

0x989F

AST-GSP1

Antenna Self Test: GSP for TX1

0x2D

0x9890

GPIO_Config_POUT

Gpio default configuration: POUT (Output Port Latch)

Read or write the output port value.

Each bit in the configuration register represents the GPIO pin with the
corresponding number

(default value 0x00: output pins are set to 0)

0x00

0x9891

GPIO_Config_PIN

Gpio default configuration: PIN (Input Port Value)

Each bit in the configuration register represents the GPIO pin with the
corresponding number

Read the input port value

0x00

0x9892

GPIO_Config_PINV

Gpio default configuration: PINV (Port Invert)

Port inversion register

Each bit in the configuration register represents the GPIO pin with the
corresponding number

0x00

0x9893

GPIO_Config_PDIR

Gpio default configuration: PDIR (Port Direction)

Each bit in the configuration register represents the GPIO pin with the
corresponding number

If set to 1, the corresponding GPIO is configured in output (whatever PEN
value). If set to 0 and if the corresponding PEN bit is set to 1, the
corresponding GPIO is configured in input.

0x00

0x9894

GPIO_Config_UPUD

Gpio default configuration: UPUD (Pull up enable register)

Each bit in the configuration register represents the GPIO pin with the
corresponding number

Set to 1, an internal pull up is connected to the corresponding GPIO.

0x03

0x9895

GPIO_Config_DPUD

Gpio default configuration: DPUD (Pull Down Enable Register)

Each bit in the configuration register represents the GPIO pin with the
corresponding number

Set to 1, an internal pull down is connected to the corresponding GPIO

0x00

Содержание PN544 C2













































































































































































Результаты поиска

Содержание PN544 C2

Отзывы:

NXP Semiconductors PN544 C2, Руководство пользователя, Страница: 154 / 172

Результаты поиска

Содержание PN544 C2

Отзывы: