NXP Semiconductors MC92602 Скачать руководство пользователя страница 28

Страница: 28 / 48

Test Setups

MC92602 Reduced Interface SerDes Design Verification Board User’s Guide, Rev. 3

4-2

Freescale Semiconductor

4.1.1

Test Setup for Full-Speed Mode

Figure 4-1

depicts the test setup for MC92602 in full-speed mode (HSE = ‘0’). The control bits are set as

follows:

•

REPE = ‘1’

•

TBIE = ‘1’

All other control bits are set to ‘0,’ except RESET, which is initially set to ‘0,’ then transitioned to ‘1’ to
start the MC92602.

Figure 4-1. Full Speed Serial Link Test Setup

4.1.2

Test Setup for Half-Speed Mode

Serial link testing may also be performed using half-speed mode (HSE = ‘1’). This reduces all frequencies
in the setup by a factor of two.

Figure 4-2

depicts the serial link test setup for using HSE and using a

divide-by-10 prescaler.

Figure 4-2. Half-Speed Serial Link Test Setup

Error Detector

CK Pattern Generator

Bit Error Rate Tester

Clean

Clock

1.25 GHz

Power

Splitter

Prescaler

Divide-by-10

Ser

ial

Reference

Clock

125 MHz

DC Blocker

CK_OUT

RF Source

MC92602DVB

(Repeater Mode)

MC92602DVB

(Repeater Mode)

RF Source

Error Detector

CK Pattern Generator

Bit Error Rate Tester

Clean

Clock

625 GHz

Power

Splitter

Prescaler

Divide-by-10

MC92602DVB

Ser

ial Data

Reference

Clock

62.5 MHz

(Repeater Mode)

DC Blocker

Содержание MC92602

















































Результаты поиска

Содержание MC92602

Отзывы:

NXP Semiconductors MC92602, Руководство пользователя, Страница: 28 / 48

Результаты поиска

Содержание MC92602

Отзывы: